to remove.
5. Remove the louver covers A, B, and C from the hood
REMOVAL OF OVEN FROM WALL (Two persons recommended to remove the oven)
. Disconnect the power supply cord, and uncoil the power supply cord.
2. Remove the turntable tray and support from the oven
cavity.
3. Remove the one () screw holding the exhaust damper
assembly to the rear stay, and remove the exhaust
damper assembly by sliding it backward.
4. Remove the two (2) screws holding the oven (outer case
cabinet) to the top cabinet.
5. Remove the hood exhaust louver referring to "HOOD
EXHAUST LOUVER REMOVAL".
6. While supporting the front of the oven, unfasten the two
Remove the oven from the wall and proceed as follows;
. Disconnect the power supply cord.
2. Open the door and block it open.
3. Remove three (3) screws holding the hood exhaust
louver to the oven, and pull it forward to remove by
pushing the right and left tabs of the hood exhaust louver.
(Refer to procedure of "HOOD EXHAUST LOUVER
REMOVAL".)
4. Remove four (4) screws holding the rear stay to the hood
fan motor or the oven, and remove it.
5. Remove the four (4) screws from the rear of the outer
case cabinet.
6. Slide the outer case cabinet back about inch (3 cm)
. Disconnect the power supply cord, remove the oven
from wall, and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer Case Removal".)
And proceed as follows.
2. Open the door and block it open.
3. Discharge high voltage capacitor.
4. Remove one () screw holding the hood duct to the oven
cavity front flange.
5. Disconnect the stop switch harness from the chassis
support and disconnect the wire leads from the fan
motor.
6. Lift up the fan motor side of the hood duct.
7. Disconnect filament leads of transformer from the
magnetron and capacitor.
8. Disconnect high voltage leads of capacitor from the
transformer.
9. Disconnect wire leads from transformer.
0. Remove two (2) screws holding the transformer to right
HOOD FAN MOTOR, HOOD DUCT, OVEN LAMP SOCKET REMOVAL AND AH SENSOR REMOVAL
. Disconnect the power supply cord and remove the ovenfrom
wall and remove outer case. (Refer to procedure of
"Removal of Oven from Wall" and "Outer case Removal"of
the base model Service Manual)
2. Open the door and block it open.
3. Discharge high voltage capacitor.
exhaust louver
6. Now, the hood exhaust louver is free.
(2) unit mounting screws holding the oven to the unit
mounting plate.
7. Remove the oven by sliding it into the arms of the unit
mounting plate and pull the power cord out of the wall
cabinet.
8. The oven is now free and can be placed on the work
surface selected for servicing the oven.
9. Installation is the reverse of this procedure.
OUTER CASE REMOVAL
to free it from retaining clips on the cavity face plate.
7. Disconnect the three (3) pin connector of the power
supply cord from the wiring harness and remove the
power supply cord together with the outer case.
8. Discharge high voltage capacitor.
CAUTION: . DISCONNECT OVEN FROM POWER
POWER TRANSFORMER REMOVAL
base plate.
Re-install
. Install by sliding the transformer on the right base plate
with its primary terminals toward the outer case.
2. Secure the transformer with two (2) screws to right base
plate.
3. Re-connect wire leads (primary and high voltage)
to the transformer and filament leads of transformer
to magnetron and high voltage capacitor. Refer to
"PICTORIAL DIAGRAM".
4. Re-install the hood duct holding the fan motor to the
oven cavity front flange with one () screw.
5. Re-connect the wire leads to the chassis support and
the fan motor, referring to "PICTORIAL DIAGRAM".
6. Re-install the outer case and check that oven is operating
properly.
CAUTION: MAKE SURE THE WIRE LEADS NEVER
4. Disconnect the 6-pin connector of the hood fan motor
from the main wire harness located at the right edge of
the hood duct and release the snap band from the hood
duct.
5. Remove the hood fan motor from the hood duct by lifting
it up.
6. Now, the hood fan motor is free.
35
SUPPLY BEFORE REMOVING OUTER
CASE.
2. DISCHARGE THE HIGH VOLTAGE
CAPACITOR BEFORE TOUCHING ANY
OVEN COMPONENTS OR WIRING.
TOUCH THE FAN BLADE.
GLMV169GSB
GLMV169GBB
GLMV169GQB
PLMVZ169GCB/C
Seite drucken