Bosch AdvancedVac 20 Handbuch - Seite 3
Blättern Sie online oder laden Sie pdf Handbuch für Staubsauger Bosch AdvancedVac 20 herunter. Bosch AdvancedVac 20 6 Seiten.
Seite drucken
OBJ_BUCH-3012-003.book Page 16 Wednesday, September 6, 2017 3:04 PM
16 | English
Technical Data
Wet/dry vacuum cleaner
Article number
Rated power input
Frequency
Container volume (gross)
Net volume (for fluids)
Dust bag contents
Vacuum (turbine), max.
Airflow (turbine), max.
Automatic Start/Stop feature
Weight according to EPTA-Procedure 01:2014
Protection class
Degree of protection
The values given are valid for nominal voltages [U] of 230 V. For lower voltage and models for specific countries, these values can vary.
Automatic Start/Stop feature*
max. power
Rated voltage
EU/AUS
220–240 V
UK
220–240 V
* Specification of the allowable load of the connected power tool (coun-
try-specific)
Assembly
Before any work on the vacuum cleaner itself, pull the
mains plug.
Mounting the Vacuum Hose
Vacuuming function (see figure A1)
– Insert the vacuum hose 16 into the hose connection piece
3 and turn it all the way in clockwise direction.
Blower Function (see figure A2)
The blower function is suitable for cleaning hard-to-reach are-
as or areas in which vacuuming is not possible, e.g. removing
leaves from gravel.
The vacuum cleaner has a blower function. Do not blow
the outgoing air randomly in enclosed areas. Use the
blower function only with the a clean hose. Dusts can be
hazardous to one's health.
– Switch on the vacuum cleaner for at least 5 seconds
(on/off switch 5/mode selector switch 5 set to the "Vacu-
uming" symbol) to clean the vacuum hose 16 of dust de-
posits.
– Turn the vacuum hose 16 all the way in anti-clockwise di-
rection and pull it out of the hose connection piece 3.
– Open the exhaust air cover 26.
– Insert the vacuum hose 16 into the hose connection piece
25 and turn it all the way in clockwise direction.
1 609 92A 43W | (6.9.17)
W
Hz
l
l
l
mbar
l/s
kg
Mounting VAC Accessories
The vacuum hose 16 is equipped with a clip system, with
min. power
which the VAC accessories (extraction adapter 17, curved
output
output
nozzle 18) can be connected.
2000 W
100 W
Fitting the extraction adapter or curved nozzle
1800 W
100 W
(see figure B)
– Fit the extraction adapter 17 or the curved nozzle 18 to the
vacuum hose 16 until the two snap fasteners 27 of the vac-
uum hose click into place.
– To disassemble, press both snap-fasteners 27 inward and
pull the components apart.
Mounting Nozzles and Tubes
– Then attach the required vacuuming accessory (floor noz-
zle, crevice nozzle, suction tube, etc.) firmly to the curved
nozzle 18 or the extraction adapter 17.
Replacing/Inserting the Dust Bag
(Dry Vacuuming) (see figures C1–C2)
You can use a dust bag (accessory) for dry vacuuming. This
makes the dust easier to dispose of.
Replacing/Inserting the Dust Bag (Accessory)
– Unlock the latches 8 and remove the vacuum lid 7.
– Pull the full dust bag 29 backwards out of the connection
flange 28 and remove it from the vacuum cleaner.
– Work the new dust bag over the connection flange of the
vacuum cleaner. Make sure that the dust bag faces com-
pletely against the interior sides of the container 1 over its
full length.
– Reattach the vacuum lid 7 again and lock the latches 8.
Changing inserts for the floor nozzle
(see figures D1 – D2)
Depending on the vacuuming work to be carried out (dry, wet,
carpet, etc.), you can clip different inserts into the floor noz-
zle 21 (e.g. rubber lip, brush insert).
– Press the release buttons 30 on the floor nozzle 21 to re-
lease the insert from the floor nozzle.
– Clip the required insert 22/23/24 into the floor nozzle 21.
UniversalVac 15
AdvancedVac 20
0 603 3D1 1..
0 603 3D1 2..
1000
50/60
15.0
8.5
11.8
240
65
–
6.9
/II
IP X4
Bosch Power Tools
1200
50/60
20.0
13.5
16.8
260
70
7.6
/I
IP X4