Bose L1 Model II Benutzerhandbuch - Seite 28

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Redner Bose L1 Model II herunter. Bose L1 Model II 32 Seiten. Portable line array systems
Auch für Bose L1 Model II: Benutzerhandbuch (32 seiten), Benutzerhandbuch (28 seiten), Technisches Datenblatt (8 seiten), Technisches Datenblatt (8 seiten), Anwendungshandbuch (13 seiten), Handbuch (15 seiten)

Bose L1 Model II Benutzerhandbuch
Svenska
Nederlands
C
M
ARE AND
AINTENANCE
Problem
With nothing plugged into
the power stand, a slight
hum or buzz is heard
B1 bass module is plugged
in, but no bass audio is
heard
B1 bass module sounds
out of balance with the
system
No mid/high sounds heard
TM
from the L1
model II
®
Cylindrical Radiator
loudspeaker
Instrument or audio source
sounds distorted
Third-party-powered sub-
woofer sounds poor when
connected to the Bass -
Line Out connector on the
power stand
B1 bass modules powered
by a third-party power
amplifier and connected to
the Bass - Line Out
connector sounds poor
Microphone is
encountering feedback
20
Italiano
Français
Svenska
What to do
• Using an AC outlet tester, test the AC outlet that the power stand is plugged into for
reversed or open (hot, neutral, and/or ground) contacts.
• If using an extension cord, make sure that the cord is also tested as above.
• Make sure you are using the included 4-wire B1 bass module cable.
• Make sure the B1 bass module cable is plugged into the Bass Module Out connector
and the cable plug is fully engaged in the connector.
• Try a different 4-wire cable.
• If available, try a different B1 bass module.
• Make sure you are using the B1 bass module 4-wire cable included with the B1 bass
module package.
• Make sure that the B1 bass module grille is facing forward toward the musicians and
audience.
• Make sure the L1 model II Cylindrical Radiator
seated in their connectors.
• Make sure connections are not bent or broken.
• Try cleaning the contacts on the loudspeaker top and bottom with electronic contact
spray cleaner.
• Make sure the Signal/Clip LED is not constantly red. If it is, lower the trim level.
• Try a different source or instrument.
• Try your source or instrument on another power stand.
• Unplug any B1 bass modules that may be connected to the power stand.
• The signal from the Bass - Line Out may be too high for the powered subwoofer; try
attenuating the signal using commercially available direct boxes or in-line pad devices.
• Try different connections to the third-party-powered subwoofer, such as balanced or
unbalanced cabling and/or a direct box.
• Check that the gain and input controls on the third-party-powered subwoofer are set
appropriately.
• If using a powered subwoofer with an adjustable crossover, set the crossover to 180Hz.
• Ensure that at least two B1 bass modules are directly connected to the Bass Module
Out connector on the power stand using a B1 bass module 4-wire cable.
• Check the gain settings on the third-party power amplifier. The volume level of the B1
bass modules powered by the power stand should be similar to the bass modules pow-
ered by the external amplifier.
• Orient the microphone so that it is not pointing directly at its respective L1 model II
®
Cylindrical Radiator
• Try a different microphone.
• Try a different position for the loudspeaker and/or vocalist on stage.
• Increase the distance from the loudspeaker to themicrophone.
• If using a vocal effects processor, make sure it is not contributing to the feedback
problem.
Nederlands
Español
loudspeaker.
Français
Deutsch
Italiano
Deutsch
Español
Dansk
®
loudspeaker top and bottom are firmly
English
English
Dansk