Bose Personalized Amplification System Handbuch zur Fehlersuche - Seite 29
Blättern Sie online oder laden Sie pdf Handbuch zur Fehlersuche für Verstärken Bose Personalized Amplification System herunter. Bose Personalized Amplification System 50 Seiten.
Auch für Bose Personalized Amplification System: Benutzerhandbuch (28 seiten)
6. Channel 1 and 2 Line Input Signal to
Noise Ratio (Dynamic Range) Tests
6.1 Place a 1/4" mono shorting plug into the
Amp 2 IN and Amp 3 IN jacks on the right
hand side of the input/output panel. This will
disable the channel 2 and 3 amplifiers while
testing the channel 1 amplifier.
6.2 On the left hand side of the input/output
panel, set the channel 1 Mic Trim control to
the 6 setting. Ensure that the Line In +20dB
gain and the Phantom Power push buttons
are not pushed in.
6.3 Using an unbalanced 1/4" phono jack
input cable, apply a 1 kHz, -10dBV signal to
the channel 1 input.
6.4 Reference a dB meter to the output level
at the Amp 1 OUT jack. Remove the input
signal and measure the A-Weighted output
level. It should be -80dB minimum.
6.5 Move the shorting plug from the Amp 2
IN jack to the Amp 1 IN jack and repeat
steps 6.1 to 6.4 for the channel 2 Line input.
7. Channel 3 and 4 Line Input Gain Tests
7.1 Place a 1/4" mono shorting plug into the
Amp 1 IN and Amp 2 IN jacks on the right
hand side of the input/output panel. This will
disable the channel 1 and 2 amplifiers while
testing the channel 3 amplifier.
7.2 On the left hand side of the input/output
panel, set the channel 3 Level control to the
6 setting.
7.3 Using an unbalanced 1/4" phono jack
input cable, apply a 1 kHz, -20dBV signal to
the channel 1 input.
7.4 Reference a dB meter to the input level.
Measure the gain output at the Bass/Amp 3
OUT jack. It should be +40.1dB + 3dB.
7.5 Repeat steps 7.1 to 7.4 for the channel 4
Line input.
TEST PROCEDURES
29
8. Channel 3 and 4 Line Input Frequency
Reponse and Distortion Tests
8.1 Place a 1/4" mono shorting plug into the
Amp 1 IN and Amp 2 IN jacks on the right
hand side of the input/output panel. This will
disable the channel 1 and 2 amplifiers while
testing the channel 3 amplifier.
8.2 On the left hand side of the input/output
panel, set the channel 4 Mic Trim control to
the 6 setting.
8.3 Using an unbalanced 1/4" phono jack
input cable, apply a 1 kHz, -20dBV signal to
the channel 1 input.
8.4 Use an 80kHz low-pass filter on your
measuring equipment. Reference a dB
meter to the input level. Measure the fre-
quency response at the Amp 1 OUT jack.
It should be 0dB + 3dB from 30Hz to 15kHz.
8.5 Measure the Total Harmonic Distortion
(THD) level at the Amp 1 OUT jack. It should
be 0.25% max at 1kHz and 1.5% max at
15kHz.
8.6 Repeat steps 8.1 to 8.5 for the channel
4 Line input.
9. Channel 3 and 4 Line Input Signal to
Noise Ratio (Dynamic Range) Tests
9.1 Place a 1/4" mono shorting plug into the
Amp 1 IN and Amp 2 IN jacks on the right
hand side of the input/output panel. This will
disable the channel 1 and 2 amplifiers while
testing the channel 3 amplifier.
9.2 On the left hand side of the input/output
panel, set the channel 3 Level control to the
6 setting.
9.3 Using an unbalanced 1/4" phono jack
input cable, apply a 1 kHz, -10dBV signal to
the channel 1 input.