Daikin R32 Split Series Installationshandbuch - Seite 8

Blättern Sie online oder laden Sie pdf Installationshandbuch für Fan Daikin R32 Split Series herunter. Daikin R32 Split Series 17 Seiten. R32 split series
Auch für Daikin R32 Split Series: Installationshandbuch (17 seiten), Installationshandbuch (16 seiten), Installationshandbuch (16 seiten), Installationshandbuch (16 seiten), Installationshandbuch (17 seiten), Installationshandbuch (16 seiten), Installationshandbuch (20 seiten), Installationshandbuch (14 seiten), Installationshandbuch (14 seiten), Betriebshandbuch (16 seiten), Betriebshandbuch (16 seiten), Betriebshandbuch (8 seiten), Installationshandbuch (16 seiten), Installationshandbuch (20 seiten), Installationshandbuch (20 seiten), Installationshandbuch (16 seiten), Installationshandbuch (16 seiten), Installationshandbuch (14 seiten), Installationshandbuch (14 seiten), Installationshandbuch (16 seiten), Installationshandbuch (17 seiten), Installationshandbuch (20 seiten), Installationshandbuch (13 seiten)

Seite drucken
Daikin R32 Split Series Installationshandbuch
5 Piping installation
Ø
Ø
i
i
Ø
Ø
p
p
t
If the temperature is higher than 30°C and the humidity is higher
than RH 80%, the thickness of the insulation materials should be at
least 20  mm to prevent condensation on the surface of the
insulation.
5.1.3
Refrigerant piping length and height
difference
What?
Maximum allowable pipe length
Minimum allowable pipe length
Maximum allowable height difference
5.2

Connecting the refrigerant piping

DANGER: RISK OF BURNING/SCALDING
CAUTION
▪ No brazing or welding on site for units with R32
refrigerant charge during shipment.
▪ During installation of the refrigeration system, joining of
parts with at least one part charged shall be performed
taking into account the following requirements: inside
occupied spaces non-permanent joints are NOT
allowed for R32 refrigerant except for site made joints
directly connecting the indoor unit to piping. Site made
joints directly connecting piping to indoor units shall be
of non-permanent type.
5.2.1
To connect the refrigerant piping to the
outdoor unit
▪ Piping length. Keep field piping as short as possible.
▪ Piping protection. Protect the field piping against physical
damage.
WARNING
Connect the refrigerant piping securely before running the
compressor. If the refrigerant piping is NOT connected and
the stop valve is open when the compressor is run, air will
be sucked in. This will cause abnormal pressure in the
refrigeration cycle, which may result in equipment damage
and even injury.
NOTICE
▪ Use the flare nut fixed to the unit.
▪ To prevent gas leakage, apply refrigeration oil ONLY to
the inside of the flare. Use refrigeration oil for R32
(FW68DA).
▪ Do NOT reuse joints.
1 Connect the liquid refrigerant connection from the indoor unit to
the liquid stop valve of the outdoor unit.
a
c b
a
Liquid stop valve
Installation manual
8
2 Connect the gas refrigerant connection from the indoor unit to
the gas stop valve of the outdoor unit.
NOTICE
It is recommended that the refrigerant piping between
indoor and outdoor unit is installed in a ducting or the
refrigerant piping is wrapped with finishing tape.
5.3
Distance
5.3.1
20 m
1.5 m
NOTICE
15 m
Do NOT exceed the unit's maximum working pressure (see
"PS High" on the unit name plate).
NOTICE
ALWAYS use a recommended bubble test solution from
your wholesaler.
NEVER use soap water:
1 Charge the system with nitrogen gas up to a gauge pressure of
at least 200  kPa (2  bar). It is recommended to pressurize to
3000 kPa (30 bar) in order to detect small leaks.
2 Check for leaks by applying the bubble test solution to all
connections.
3 Discharge all nitrogen gas.
5.3.2
DANGER: RISK OF EXPLOSION
Do NOT start the unit if it is vacuumed.
1 Vacuum the system until the pressure on the manifold indicates
−0.1 MPa (−1 bar).
2 Leave as is for 4-5 minutes and check the pressure:
Does not change
Increases
3 Vacuum the system for at least 2 hours to a manifold pressure
of −0.1 MPa (−1 bar).
4 After turning the pump OFF, check the pressure for at least
1 hour.
5 If you do NOT reach the target vacuum or CANNOT maintain
the vacuum for 1 hour, do the following:
▪ Check for leaks again.
▪ Perform vacuum drying again.
b
Gas stop valve
c
Service port

Checking the refrigerant piping

To check for leaks
▪ Soap water may cause cracking of components, such
as flare nuts or stop valve caps.
▪ Soap water may contain salt, which absorbs moisture
that will freeze when the piping gets cold.
▪ Soap water contains ammonia which may lead to
corrosion of flared joints (between the brass flare nut
and the copper flare).
To perform vacuum drying
If the pressure...
There is no moisture in the
system. This procedure is
finished.
There is moisture in the
system. Go to the next step.
Then...
RXJ20~35A
R32 split series
3P482320-17X – 2021.12