DSC PC2550 Gebrauchsanweisung - Seite 3
Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Sicherheitssystem DSC PC2550 herunter. DSC PC2550 8 Seiten.
Auch für DSC PC2550: Gebrauchsanweisung (17 seiten), Gebrauchsanweisung (3 seiten)
A WORD ABOUT YOUR SYSTEM
The PC2550 Security System has been designed to give you the greatest possible
flexibility and convenience. Read this manual carefully and become familiar with the
operation of your Security System. Your installer will tell you which commands listed
in this manual apply to your system. Fill out the SYSTEM REFERENCE sheet in this
manual and store it in a safe place for future reference. The label provided for the
inside of the keypad door can be used to record which sensors are on each zone.
IMPORTANT NOTE
Remember that no security system can prevent emergencies. It is only
intended to alert you in case of an emergency and should not take the
place of prudent security practices or life and property insurance.
Notes for UL Installations
The PC2550 is suitable for the following UL installations:
• Household Fire and Grade A Burglary
• Grade A Local
• Grade B Central Station
• Grade A Police Station Connect with Basic Line Security
• Grade C Central Station
• Grade A Police Connection with Basic Line Security
It is important to test your system every week. To do this, first inform the monitoring
station that you are testing your system. Then, with the system disarmed, activate all
detection sensors one at a time and observe the zone light come on at the keypad
as each sensor is activated. Perform a bell test by entering [ ][6][Master Code][8]
with the system disarmed. The PC2550 can be programmed at the time of installation
to automatically perform a test transmission to the monitoring station on a regular
basis. If the system has not been programmed for this automatic test, call the
monitoring station for instructions on how to perform a test transmission. Don't forget
to inform the monitoring station when you have finished your test.
Check to see if the "Trouble" light is on when arming the system. See the
Trouble Display section in this manual for a description of the different trouble
conditions. Contact your installer for assistance if the trouble condition cannot
be located and corrected.
HOW YOUR SYSTEM WORKS
Your Security System is made up of a control panel, one or more keypads, and
various detectors and sensors. The control panel will be mounted out of the way in
a utility room or basement. The metal cabinet contains the system electronics, fuses
and stand-by battery. There is normally no reason for anyone but the installer to
have access to the control panel. The keypad(s) have an audible indicator, display
lights and command entry keys. The keypad is used to send commands to the
system and to display the current system status.
convenient areas close to the exit-entry doors. The security system has up to eight
zones or areas of protection. Each zone used will have connected to it various
sensors, such as door or window contacts, motion detectors, glassbreak detectors
and vibration or shock sensors. When a sensor is in alarm, a keypad light will be
on to indicate which zone is in alarm.
Keypads are mounted in
2
MASTER CODE
The 4 digit Master Code is used for arming and disarming the system, for programming
additional access codes, and for changing other features. The Master Code will be
supplied to you by your installer. All keypad entries are made by pressing one key
at a time and may be changed by you at any time if the installer selects an option. For
additional access codes, see Programming Additional Access Codes.
ARMING
Close all protected doors and windows and stop movement in areas covered by
motion detectors. If the "Bypass" light is ON, be sure zones are being
intentionally bypassed before arming the system (see Zone Bypassing).
Check to see that the "Ready" light is ON (all zones are closed). The system
cannot be armed unless the "Ready" light is ON. Enter a [4 digit access code].
As each digit is entered, the keypad sounder will beep. Once the correct access
code is entered, the "Armed" light will come ON and the keypad sounder will
beep quickly. If the access code was entered incorrectly or the "Ready" light was
not ON, the keypad sounder will beep steadily for 2 seconds.
When the correct code is entered and the system is armed, exit through the door
indicated by your installer as the exit-entry door. The exit time may be changed
by your installer (please refer to the Quick-Arm feature).
Arming and Commercial Installations
When an Access Code is entered to arm the system, the bell or siren will sound a
short tone to indicate that the system is being armed. If your security system is
programmed to report to a monitoring station, the keypad will also sound a tone to
indicate that the monitoring station has been advised of the arming of the system.
If the system is being armed and the bell or siren fails to sound, or if the keypad
does not sound a tone to acknowledge that the monitoring station has been
advised of the arming, arrange for service for the system.
AUTO-BYPASS OPTION - HOME-AWAY ARMING
This feature, if selected by your installer, will allow you to arm your system with
any valid access code and the system will automatically bypass the interior zones
if those interior zones have been designated as home-away zones by the installer.
When activated, the "Bypass" light will come ON. If you exit within the allowed
exit time, the system will automatically reactivate the interior zones. This feature is
designed to save the user from having to manually bypass interior zones each
time they wish to arm the system and remain at home.
In residential applications where the system has been armed and the interior
zones are automatically bypassed, the interior zones can be reactivated from a
keypad outside the interior zones protection area (e.g. a bedroom). To reactivate
the interior zones, press [ ] then [1] and the "Bypass" light will go out.
ENTRY DELAY OFF ARMING
If you wish to arm your system and eliminate the entry delay, enter [ ][9] before
your access code. The "Armed" light will flash as a reminder that the system is
armed and has no entry delay. An entry through any zone programmed as a
delay zone will create an instant alarm.
e.g. To arm without entry delay.....Press [ ][9][Access Code]
3