Daisy Under Bench Roller Installationsanleitung Handbuch - Seite 10

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Outdoor-Einrichtung Daisy Under Bench Roller herunter. Daisy Under Bench Roller 12 Seiten.

OPERATION
Programming New Remote Control
Every new remote control needs to be programmed (paired) with the
control housing.
To program a remote control simply:
1. Press any direction button on the control housing unit to wake up
the control housing.
2. Press the Program button for 1 to 3 seconds.
3. Press any button on the remote control for 1 second (unit may
start operation as remote control is now programmed) .
Note: Only one button is required to be pressed to program all the
buttons on the remote control unit.
LED Indicator Light Logic
1. When motor is operating, the battery LED will show red as it's
loading the battery and drawing the power.
2. Red Light is an indicator of what control housing is doing, it is NOT
an error indicator.
3. Battery charging lights may 'flicker' to indicate the charge rate.
The faster the 'flicker' the faster the charge (may look like a
different colour) the slower the 'flicker' the slower the charge.
Solar light:
Red Light = Charging the battery, voltage <10.5V
Yellow light = Charging the battery, voltage (10.5V~11V)
Green light = Full charged, battery voltage >11V
AC charger light:
Red Light = Charging the battery, voltage <10.5V
Yellow light = Charging the battery, voltage (10.5V~11V)
Green light = Full charged, battery voltage >11V
Battery light:
Without Solar or AC Charging, after the motor operation (pressing a
button not in auto roll):
Red light = battery voltage <10.5V – or while AC plugged in battery
may stay red indicating available – not a fault.
Yellow light = battery voltage (10.5V~11V)
Green light = battery voltage >11V
Regularly check tension of all screws and mounting bolts.
Programming New Remote Control
Every new remote control needs to be programmed (paired) with the
To program a remote control simply:
1. Press any direction button on the control housing unit to wak
2. Press the Program button for 1 to 3 seconds
Daisy Power Program Button
3. Press any button on the remote control for 1 second
(unit may start operation as remote control is now programm
Green light = Full charged, battery voltage >11V
AC charger light:
Red Light = Charging the battery, voltage <10.5V
Yellow light = Charging the battery, voltage (10.5V~11V)
Green light = Full charged, battery voltage >11V
Battery light (Without Solar or AC Charging) after the motor operation (pressing a button not in auto roll):
Red light = battery voltage <10.5V – or while AC plugged in battery may stay red indicating available
Note: only one button is required to be pressed to program all the bu
Yellow light = battery voltage (10.5V~11V)
Green light = battery voltage >11V
LED Indicator Light logic
Note:
1. When motor is operating, the battery LED will show red as it's
2. Red Light is an indicator of what control housing is doing, it is
3. Battery charging lights may 'flicker' to indicate the charge rate
(may look like a different colour) the slower the 'flicker' the sl
Solar light:
Red Light = Charging the battery, voltage <10.5V
Regularly check tension of all screws and mounting bolts
Yellow light = Charging the battery, voltage (10.5V~11V)
Test Procedure
If there are any issues with the operation or the unit is unresponsive, before a service call can be requested, plug in
and turn on AC charger continually for a minimum of 3 days (note keep all 240v cords and charger protected from
weather and further than 4m away from pool water)
AC charger is normally warm when working
If Daisy Power unit is non-responsive:
Is the unit responsive at all...any partial movement, humming, clicks or any response?
What is the light display?
Note:
if AC charger is NOT plugged in, lights will stay illuminated for approximately 1 minute after any button press
then turn off
if AC charger IS plugged in lights will stay on all the time (see Indicator lights image below)
Before a service call can be requested (to be completed by end user):
Plug in and turn on AC charger continually for a minimum of 3 days (note keep all 240v cords and charger protected
from weather and further than 4m away from pool water)
AC charger is normally warm when working
What is happening when you test (press button) now?
AC charger when plugged in will operate from the AC charger through PCB at full power
Daisy Power
Program Button
Remote