DSC 3g4000 Installationshandbuch - Seite 7
Blättern Sie online oder laden Sie pdf Installationshandbuch für Mobiltelefon DSC 3g4000 herunter. DSC 3g4000 8 Seiten. 3g (hspa) wireless alarm communicator
Seite drucken
MODIFICATION STATEMENT
Digital Security Controls has not approved any changes or modifications
to this device by the user. Any changes or modifications could void the
user's authority to operate the equipment.
Digital Security Controls n'approuve aucune modification apportée à
l'appareil par l'utilisateur, quelle qu'en soit la nature. Tout changement
ou modification peuvent annuler le droit d'utilisation de l'appareil par
l'utilisateur.
INTERFERENCE STATEMENT
This device complies with Part 15 of the FCC Rules and Industry Canada
licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device
must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables
aux appareils radio exempts de licence. L'exploitation est autorisée aux
deux conditions suivantes : (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage
radioélectrique subi, même si le brouillage est susceptible d'en
compromettre le fonctionnement.
WIRELESS NOTICE
This equipment complies with FCC and IC radiation exposure limits set
forth for an uncontrolled environment. The antenna should be installed and
operated with minimum distance of 20 cm between the radiator and your
body.
Antenna gain must be below:
Frequency band
GSM 850 / FDD V
PCS 1900 / FDD II
This transmitter must not be co-located or operating in conjunction with
any other antenna or transmitter.
Cet appareil est conforme aux limites d'exposition aux rayonnements de la
IC pour un environnement non contrôlé. L'antenne doit être installé de
façon à garder une distance minimale de 20 centimètres entre la source de
rayonnements et votre corps.
Gain de l'antenne doit être ci-dessous:
Bande de fréquence
GSM 850 / FDD V
PCS 1900 / FDD II
L'émetteur ne doit pas être colocalisé ni fonctionner conjointement avec à
autre antenne ou autre émetteur.
FCC CLASS B DIGITAL DEVICE NOTICE
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
CAN ICES-3 (B) / NMB-3 (B)
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de classe B est conforme à la norme canadienne
ICES-003.
FCC ID:F53143G4000
US:F53MO00B3G4000
IC: 160A-3G4000
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and
telephone network must comply with the applicable FCC Part 68 rules and
WARNING: To satisfy FCC RF exposure requirements for mobile transmitting devices, a separation distance of 20cm or more
must be maintained between the antenna of this device and persons during device operation.
requirements adopted by the ACTA. A compliant telephone cord and modular
plug is provided with this product. It is designed to be connected to a
compatible modular jack that is also compliant. See installation instructions for
details.
Ringer Equivalence Number (REN)
The REN is used to determine the number of devices that may be connected to
a telephone line. Excessive RENs on a telephone line may result in the devices
not ringing in response to an incoming call.
In most but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as determined
by the total RENs, contact the local Telephone Company. For products
approved after July 23, 2001, the REN for this product is part of the product
identifier that has the format. US: AAAEQ##TXXXX. The digits represented
by ## are the REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier
products, the REN is separately shown on the label.
Incidence of Harm
If this equipment 3G4000 causes harm to the telephone network, the telephone
company will notify you in advance that temporary discontinuance of service
may be required. But if advance notice is not practical, the Telephone
Company will notify the customer as soon as possible. Also, you will be
advised of your right to file a complaint with the FCC if you believe it is
necessary.
Changes in Telephone Company Equipment or Facilities
The Telephone Company may make changes in its facilities, equipment,
operations or procedures that could affect the operation of the equipment. If this
happens the Telephone Company will provide advance notice in order for you
to make necessary modifications to maintain uninterrupted service.
Equipment Maintenance Facility
3G4000
If trouble is experienced with this equipment for repair or warranty
6.21 dBi
information, please contact the facility indicated below. If the equipment is
3.76 dBi
causing harm to the telephone network, the Telephone Company may request
that you disconnect the equipment until the problem is solved. This equipment
is of a type that is not intended to be repaired by the end user.
DSC c/o APL Logistics, 757 Douglas Hill Rd., Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state
public utility commission, public service commission or corporation
commission for information.
Alarm dialling equipment must be able to seize the telephone line and place a
call in an emergency situation. It must be able to do this even if other equipment
3G4000
(telephone, answering system, computer modem, etc.) already has the
6.21 dBi
telephone line in use. To do so, alarm dialling equipment must be connected to
a properly installed RJ-31X jack that is electrically in series with and ahead of
3.76 dBi
all other equipment attached to the same telephone line. Proper installation is
depicted in the figure below. If you have any questions concerning these
instructions, you should consult your telephone company or a qualified
installer about installing the RJ-31X jack and alarm dialling equipment for you.
This product meets the applicable Industry Canada technical specifications.
The Ringer Equivalence Number (REN) indicates the maximum number of
devices allowed to be connected to a telephone interface. The termination of an
interface may consist of any combination of devices subject only to the
requirement that the sum of the RENs of all the devices not exceed five.
The Ringer Equivalence Number (REN) for this terminal equipment is 0.0.
Le nombre équivalent de sonneries (REN) de cet appareil terminal est 0.0.
The reference to the 3G4000 throughout this manual is applicable to the
following model numbers: 3G4000 and 3G4000RF.
NIST Validation of encryption algorithm AES128 certificate No. 3091.