DSC RXL2-433 Installationshandbuch - Seite 2
Blättern Sie online oder laden Sie pdf Installationshandbuch für Kontrolleinheit DSC RXL2-433 herunter. DSC RXL2-433 2 Seiten. Universal wireless relay module
Seite drucken
2.4 Connecting to a Security Gate
Mount the RXL2-433 inside the gate enclosure as high as possible to ensure that water will not
collect inside the receiver. Connect relay #1, NO and C terminals, to the Open/Close
terminals on the gate motors terminal strip. Please consult the gate opener instructions for
proper connection. The RXL2-433 is defaulted to a 'Momentary' relay output, if you have
changed the output to a different type you must reset the relay to 'Momentary' for the gate to
operate correctly. See Section "How to Program Relay #1 Out-put."
2.5 Connecting to an X-10 Powerflash Module
When connecting an X-10 Powerflash module to the RXL2-433, different lights within or outside
the home can be controlled, such as table lamps, or porch and driveway lights that illuminate
the entry/exit path. This can be achieved by setting the RXL2-433 a number of various ways
depending on desired operation.
• The wireless key can toggle a latched output, triggering the X-10 Powerflash module,
providing direct control of lighting. This feature can be controlled by programming the
RXL2-433 Relay # 1 or #2 to a 'Latch' type. See "How to Program Relay #1 Output."
• The wireless key can turn on an output for 60 seconds lighting an entry pathway as a
customer approached the home. This feature can be controlled by programming the
RXL2-433 Relay #1 or #2 to 'Timed' type. See "How to Program Relay #1 Output."
Section 3: Wireless Keys
This section describes how to enroll wireless keys. For more information on these keys, read
the instruction sheet included with each key.
3.1 Enroll and Program Wireless Keys
For wireless keys to operate on a system, you need to enroll them You can enroll 10 buttons
per relay for a maximum of 20 buttons using up to 20 different remotes to control either of the
2 on-board relays.
Enroll Wireless Keys to Relay #1
1. Remove the small door and upper case on the RXL2-433.
2. Ensure the unit is plugged into a 120VAC outlet to power the RXL2-433 using the supplied
transformer. You can plug in the adapter to any outlet for programming and then
move it to its permanent location once complete. The RXL2-433 has EEPROM built in
and will store any programmed information even if the unit is unplugged or moved in
the future.
3. Locate the program button directly behind the power plug. Press and release ONE time
to learn buttons into Relay #1. After 2 seconds the LED will Flash ON and OFF slowly
confirming it is ready to learn remote buttons.
4. Press the button of any DSC remote described in section 1.2 that you would like to control
Relay #1. Once a button is learned, the LED will flash quickly to confirm it had
received and learned that button.
NOTE: The RXL2-433 will time out if it does not see any button presses within 10 seconds. If
the unit times out complete steps 3-4 to add a button or key.
How to Program Relay #1 Output
Relay Output:
Momentary
Latched
Timed (60 seconds)
Validity (only good with 12 channel)
Jumpers:
JP3 IN, JP4 IN
JP3 OUT, JP4 IN
JP3 IN, JP4 OUT
JP3 OUT, JP4 OUT
*Validity output can only be used with WS4959 and will energize the relay for as long as the
button on the remote is held. This is useful for operation when an unspecified energize time
is necessary.
Enroll Wireless Keys to Relay #2
1. Remove the small door and upper case on the RXL2-433.
2. Make sure the unit is plugged into a 120VAC outlet to power the RXL2-433 using the
supplied transformer. You can plug in the adapter to any plug for programming and then
move it to its permanent location once complete. The RXL2-433 has EEPROM built in and
will store any programmed information even if the unit is unplugged or moved in the future.
3. Locate the program button directly behind the power plug. Press and release TWICE to
learn buttons into Relay #2. The LED will flash a double flash.
4. Press the button of any DSC remote described in section 1.2 that you would like to control
Relay #2. Once a button is learned, the LED will flash quickly to confirm it had received and
learned that button.
NOTE: The RXL2-433 will time out if no buttons are pressed within 10 seconds. If the unit times
out, complete steps 3-4 to add a button or key.
How to Program Relay #2 Output
Relay Output:
Momentary
Latched
Timed (60 seconds)
Validity (only good with 12 channel)
*Validity output can only be used with WS4959 and will energize the relay for as long as the
button on the remote is held. This is useful for operation when an unspecified energize time
is necessary.
3.2 Deleting Wireless Keys
By entering the DELETE mode within the RXL2-433 all remotes will be removed and
subsequently must be re-enrolled before they will operate again. To enter DELETE mode, press
and HOLD the program button on the receiver. After 10 seconds the LED will turn On/Off 5
times to indicate all remotes in the system have been deleted. Follow steps 3-4 in Section 3.1 to
re-enroll desired remotes.
Section 4: Installation
4.1 Testing the Receiver
If range is poor, verify the antenna is not obstructed and that it is hanging freely towards the
ground. If range is still unacceptable, move the receiver to a different location at least 24 inches
away from its current location.
4.2 Mounting the Transformer
If connecting the transformer to an electrical outlet mounted on the ceiling of a garage, please
use the supplied velcro to secure the body of the transformer to the ceiling. For good adhesion
please ensure the surface of the ceiling and transformer are clean prior to attaching the velcro..
Section 5: Troubleshooting
1. I press the remote button and I do not hear a 'click' at the receiver.
Make sure the remote button that you want to operate with the RXL2-433 is enrolled properly.
See section 3.1
Jumpers:
JP1 IN, JP2 IN
JP1 OUT, JP2 IN
JP1 IN, JP2 OUT
JP1 OUT, JP1 OUT