DT Research DT180P Betriebshandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Betriebshandbuch für Controller DT Research DT180P herunter. DT Research DT180P 2 Seiten. Embedded controller/system

Seite drucken
DT180P/ DT180T
Precautions
•
Always exercise care when operating and handling the DT180P/ DT180T.
•
Never disassemble any portion of the enclosure. It will void any product warranty on the
DT180P/ DT180T.
•
Do not use any AC/DC adapter other than the one provided with the device or acquired from the
manufacturer or its partners.
•
In the unlikely event that smoke, abnormal noise, or strange odor is present, immediately power
down the DT180P/ DT180T and disconnect all power sources.
•
Please report the problem to your device provider immediately.
THE DT180P/ DT180T
Front View
A
B
C
Audio jacks
A
Power button
B
C
USB 2.0 (2)
Powering ON and OFF
The Power Button is located in the front of the DT180P/ DT180T. The Power Button may be
configured to function differently depending on the power options of the operating system. In
general, to turn the DT180P/ DT180T on, push and release the Power Button on the front bezel.
The adjacent power LED will be lit (blue) and the corresponding interface will be displayed on the
display monitor.
To turn off the device, again depending on software operating system, push and release the Power
Button or use a software shutdown interface. In the event of system lockup, the Power Button may
be used to perform a reset on the device. To do that, push and hold the Power Button for at least 4
seconds. The system will shut down and all unsaved work may be lost. Pushing on the Power Button
again will restart the device.
2
ENGLISH
Rear View
D
E
F
G
H
D
G
Ethernet port
RS232 COM port
E
H
HDMI port
DC-in
F
VGA port
Device Ports
The DT180P/ DT180T features an optimal set of I/O ports while preserving the compact size of
the system. The HDMI connector, Network (10/100/1000 BaseT Ethernet), and Power ports are
supplemented by a set of two USB 2.0 and two Audio ports. Through its USB ports, the DT180P/
DT180T supports a wide range of USB-based peripherals. These peripherals are applicable in
providing the means for software installation, application storage, data storage, and system
software recovery and updates.
Memory and Storage
The DT180P/ DT180T may be available in storage configurations ranging 8GB of flash memory
or 32GB to 64GB SSD. Depending on base software configuration, the user may use the internal
memory of the DT180P/ DT180T for user's installed software and storage. The user may also
supplement storage space with USB-based peripherals such as flash disks, disk drives, etc. RAM
capacity is up to 2GB.
VESA Mounting Bracket Installation Guide for DT180P/ DT180T
The DT180P/ DT180T package includes a VESA-compliant mounting bracket (1) which mounts the
DT180P/ DT180T (2) onto a VESA-compatible monitor or display.
NOTE: The VESA Mounting Bracket is compatible with most displays and monitors that support the VESA standard.
Step1:
Step2:
•
Locate the existing mounting holes on
•
Remove the two M3 screws (3) originally
the monitor.
on the DT180P/ DT180T signage
•
Line the bracket holes up with the holes
appliance.
on the back of the monitor, as shown
•
Place the DT180P/ DT180T (2) on the
to the right.
bracket rail with the interface ports
•
Place the screws to hold the mounting
side facing downwards so that the two
bracket in place and tighten the screws
mounting holes on the appliance are
(do not over-tighten).
aligned with the existing holes on the rail
(see picture).
Step3:
•
Apply and tighten the screws
into their original locations and
make sure that the bracket and
the DT180P/ DT180T are properly
secured.
3
ENGLISH