Attwood Sahara 4505-1 Einbauanleitung - Seite 2

Blättern Sie online oder laden Sie pdf Einbauanleitung für Water Pump Attwood Sahara 4505-1 herunter. Attwood Sahara 4505-1 4 Seiten. Sahara series automatic bilge pumps

Seite drucken

WARNING: Do not allow sealants containing acetic acid

(smells like vinegar) such as silicone rubber sealant to contact the

plastic pump housing or thru-hull connector. Such sealants can

attack the plastic, causing the pump housing to crack, resulting in

pump failure.

5. Insert thru-hull connector through the hole and tighten to hold

the thru-hull connector firmly in place. CAUTION: Do not

overtighten the nut.

WIRING INSTRUCTIONS

WARNING: Be certain that power source is 12-volt D.C. Higher

voltage will damage the pump.

1. Using the full length of wire provided (and additional wire if

necessary), connect wires to the pump as shown in the

diagram. (See Figure 2.)

Figure 2

12 Volt Battery

Suitable Fuse

(see chart)

2. Route wires out of the way and secure them to the bulkhead to

avoid pulling.

3. Using butt connectors sized for 16-gauge wire, splice fuse

holder into positive lead (brown) between the battery and switch.

Position fuse holder in a location that is easily accessible for

changing fuses.

IMPORTANT: Use fuses of the proper amperage (See Specification

Chart at top of sheet).

WARNING: FAILURE TO PROPERLY FUSE AND MAKE THE

APPROPRIATE WATERPROOF CONNECTIONS WILL VOID THE

PRODUCT WARRANTY.

4. Install a Three-Way Switch (Attwood No. 7615A) that allows for

automatic or manual switching modes.

5. Turn the pump on and twist the Test Knob clockwise to check

operation. Feed water into the pump. If output appears to be too

low, check the wire connections. Reversed connections result in

opposite impeller rotation that drastically reduces capacity and

can cause premature pump failure.

CARE AND MAINTENANCE

Occasionally check your pump to be certain debris is not jamming

the impeller and/or float within the housing. Use the test knob by

rotating in a clockwise direction. Careful attention will guarantee

outstanding pump performance.

To clean the water chamber, remove pump housing from the mounting

base by pressing in tabs on sides. Lift the pump housing away.

(See Figure 3.)

To clean the impeller, remove the impeller guard screw and lift the

impeller guard.

Black

Brown/White or Tan

Manual

Off

Brown

Automatic

Test Knob

3-Way Switch

#7615A

Figure 3

Remove (1)Screw

Remove all debris that has accumulated in pump chamber and

around the impeller. Ensure that all debris is removed from strainer

slots around the pump base.

Inspect the impeller to ensure that it is firmly attached to shaft and

is not cracked or broken.

Replace impeller guard, screw, and pump housing on base. Be

certain that all tabs are fully engaged.

Periodically check the electrical connections to ensure they are

water-resistant and mounted high and dry.

Do not use household cleaners on the pump because many of

them may damage the pump materials.

ATTWOOD LIMITED WARRANTY

ATTWOOD CORPORATION, 1016 North Monroe, Lowell, Michigan 49331

("Attwood") warrants to the original consumer purchaser that Attwood brand

products will be free from defects in materials and workmanship under

normal use and service for three years from the date of original consumer

purchase. This warranty does not extend to any batteries or fuses used with

the product. This limited warranty is not applicable if the product has been

damaged by accident, improper installation, unreasonable or improper use,

lack of proper maintenance, unauthorized repairs or modifications, normal

wear and tear, or other causes not arising out of defects in materials or

workmanship. Attwood products are warranted for use on pleasure boats.

Any other use — including but not limited to commercial, racing, or non-

marine use — are not covered under this warranty. Attwood's obligation

under this warranty is limited to repair of the product at Attwood's plant or

replacement of the products at Attwood's option without expense to the

original consumer purchaser. Any expenses involved in the removal,

reinstallation or transportation of the product are not covered by this

warranty. The product must be returned to Attwood's plant at the address

above, postage prepaid, and insured with proof of original purchase

including date. If Attwood is unable to replace the product and repair is not

commercially practical or cannot be timely made, or if the original consumer

purchaser is willing to accept a refund in lieu of repair or replacement,

Attwood may refund the purchase price, less an amount for depreciation.

The acceptance by Attwood of any product returned or any refund provided

by Attwood shall not be deemed an admission that the product is defective

or in violation of any warranty. Products that are replaced or for which a

refund is issued become the property of Attwood.

THIS WARRANTY IS ATTWOOD'S ONLY EXPRESS WARRANTY OF

THIS PRODUCT. NO IMPLIED WARRANTY SHALL EXTEND BEYOND

THREE (3) YEARS FROM THE DATE OF ORIGINAL CONSUMER

PURCHASE. ATTWOOD SHALL NOT BE LIABLE FOR ANY DAMAGES,

FOR LOSS OF USE OF THIS PRODUCT, NOR FOR ANY OTHER

INCIDENTAL OR CONSEQUENTIAL DAMAGES, COSTS OR EXPENSES.

Some states do not allow limitations on how long an implied warranty lasts

or the exclusion or limitation of incidental or consequential damages, so the

above limitations and exclusions may not apply to you. This warranty gives

you specific legal rights, and you may have other rights which vary from

state to state.

1016 N. Monroe Street, Lowell, MI 49331-0260 www.attwoodmarine.com

Impeller Guard

Depress (2)Tabs