3onedata ICPE2300A-BW-8A25-1GC3GT-PD2P12 48 Handbuch zur Schnellinstallation - Seite 2
Blättern Sie online oder laden Sie pdf Handbuch zur Schnellinstallation für Netzwerk-Router 3onedata ICPE2300A-BW-8A25-1GC3GT-PD2P12 48 herunter. 3onedata ICPE2300A-BW-8A25-1GC3GT-PD2P12 48 5 Seiten. Industrial indoor 5g wireless router
Seite drucken2.4G/5.8G bridge signal strength indicator (
3.
10/100/1000Base-T(X)
Gigabit
(LAN1-LAN3)
4.
10/100/1000Base-T(X) Gigabit PoE copper port
and 1000Base-X Gigabit SFP combo port(WAN)
5.
Ethernet port indicators, from top to bottom in turn
they are:
Gigabit copper port indicator (LAN1-LAN3)
PoE indicator (PoE)
Gigabit COMBO port indicator(WAN)
6.
RESET button
7.
CONSOLE port
8.
5G indicators, from left to right in turn they are:
5G NR indicator(5G)
5G NR bridge signal strength indicator (
9.
USB, SD, SIM indicators, from left to right in turn
they are:
USB interface indicator(USB)
SD card indicator(SD)
SIM card indicator(SIM1-SIM2)
10.
USB interface(USB)
11.
SD/SIM card slot(SIM)
12.
Terminal blocks for power1 input (V1)
13.
Terminal blocks for power2 input (V2)
14.
Relay output alarm(RELAY)
15.
5.8G antenna interface(5.8G)
16.
2.4G antenna interface(2.4G)
17.
5G Sub-6G antenna interface(5G)
18.
Grounding screw
19.
DIN-Rail mounting kit
【Mounting Dimension】
Unit: mm
)
copper
port
Notice Before Mounting:
)
Don't place or install the device in area near water or
moist, keep the relative humidity of the device
surrounding between 5%~95% without condensation.
Before power on, first confirm the supported power
supply specification to avoid over-voltage damaging the
device.
The device surface temperature is high after running;
please don't directly contact to avoid scalding.
【DIN-Rail Mounting】
The product adopts 35mm standard DIN-Rail mounting which
is suitable for most industrial scenes, mounting steps as
follows:
Step 1
Check if the DIN-Rail mounting kit is installed firmly.
Step 2
Clip the upper part of the DIN-Rail mounting kit, i.e.
Step 3
Step 4
【Disassembling DIN-Rail】
Step 1
Step 2
Step 3
2 / 5
the fixed side, into the DIN rail.
Press the lower side of the device and insert the
lower part of DIN-Rail mounting kit (the side with
spring support) into DIN-Rail.
Tips:
The DIN-Rail spring support is a metal sheet that can
move up and down, and there will be a sound after it is
clamped in.
Check and confirm the product is firmly installed on
DIN rail, then mounting ends.
Power off the device.
Use a slot type screwdriver or other tools to move the
DIN rail spring support downward; At the same time,
move the lower side of the device outward and move
out the lower part of the DIN rail mounting kit.
Lift the device upward slightly, move out the upper
part of DIN-Rail mounting kit. Disassembling ends.
Notice before power on:
Power ON operation: First insert the power supply
terminal block into the device power supply interface,
then plug the power supply plug contact and power on.
Power OFF operation: First, remove the power plug,