Duevi EZY-LAN Handbuch - Seite 10
Blättern Sie online oder laden Sie pdf Handbuch für Sicherheitssensoren Duevi EZY-LAN herunter. Duevi EZY-LAN 12 Seiten. Wireless alarm panel with ethernet + wi-fi + gsm + lte
Auch für Duevi EZY-LAN: Benutzerhandbuch (4 seiten), Benutzerhandbuch (5 seiten)
Seite drucken12.8 Logics (SETUP)
A logic is a rule that creates a cause-effect link
between a certain event and an operation (Action
or Scenario) that the control panel must perform
every time that event occurs.
The LOGICS page contains the list of all created
logics.
Pressing the icon
Pressing the icon
settings, where you can change its properties.
•
Logic name: is the name with which the logic
is identified in all menus, notifications, events,
etc
•
Triggering event: represents the event that
triggers
the
execution
operations.
The
available for this event:
-
Sector event:
Alarm L1 in sectors (OR logic)
Alarm L2 in sectors (OR logic)
Sectors disarmed (AND logic)
Sectors armed (AND logic)
Sectors armed (OR logic)
Entry delay
Exit delay
Chime
24H alarm
Silent alarm
-
Zone event:
Zone detection (only zones set in mode
"Only use for logic")
-
Panel event:
Panic Alarm
Manumission alarm
•
Operation to execute (at the beginning of the
event): represents what the control panel will
perform each time the triggering event starts.
This operation can be an Action or a Scenario.
•
Other operation to execute (at the end of the
event): it represents what the control panel will
perform each time the triggering event ends.
This operation can be an Action or a Scenario.
12.9 Monitoring Stations (SETUP)
The control panel can send events to a Monitoring
Station with Contact-ID SIA-DC09 receiver, via
internet connection (on local network or LTE
network).
The MONITORING STATIONS page contains the
list of all created Monitoring stations.
Pressing the icon
station.
(trash can) deletes the logic.
(gear) you enter the logic
of
the
following
settings
(trash can) deletes the
Pressing the icon
settings, where you can change its properties.
•
Sending events to the Monitoring Station:
Activate / Deactivate
•
Monitoring Station name: is the name with
which the Station is identified in all menus,
notifications, events, etc
•
Supervision interval: time interval in hours
after which the control panel sends the Life
Test to the station
•
Associated sectors: represents the sectors for
which events are sent
•
Prefix: prefix of the account code (ONLY IF
NECESSARY) - provided by the Monitoring
Station
•
Client Account: client identification code -
defined
provided by the Monitoring Station
are
•
Server IP address: IP address of the receiver
- provided by the Monitoring Station
•
Port: communication port of the receiver -
provided by the Monitoring Station
•
CONNECTION TEST: send the Life Test code
to test the parameters
•
Codes: this section indicates all the events
(with relative standard codes) that the control
panel can send to the monitoring station.
In the Contact-ID standard each event is
identified
It is possible to modify the value associated
with each event (if the Monitoring Station uses
different
The sending of each event can be enabled /
disabled with the ON / OFF switch.
12.10 Other commands (SETUP)
Riceive from panel
Upload the configuration present in the control
panel to the software interface. When you enter
SETUP it is loaded automatically.
Send to panel
Send to the control panel the configuration
currently displayed in the software interface.
Save settings on disk (Windows App only)
Save to file the configuration currently displayed
in the software interface.
Load settings from disk (Windows App only)
Load a configuration previously saved on file into
the software interface.
(gear) you enter the station
with
a
numerical
code.
codes).