Casio 1517 Benutzerhandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Siehe Casio 1517 herunter. Casio 1517 10 Seiten.

Seite drucken

To turn the auto light switch on and off

In the Timekeeping Mode, hold down D for one second to turn the auto light

switch on (A-LIGHT ) and off (A-LIGHT).

• In order to protect against running down the battery, the auto light switch is

automatically turned off approximately two or three hours after you turn it

on. Repeat the above procedure to turn the auto light switch back on if you

want.

• The

mark next to A-LIGHT is on the display in all modes while the auto

light switch is turned on.

Warning!

• Never try to read your watch when mountain climbing or hiking in

areas that are dark or in areas with poor footing. Doing so is

dangerous and can result in serious personal injury.

• Never try to read your watch when running where there is danger of

accidents, especially in locations where there might be vehicular or

pedestrian traffic. Doing so is dangerous and can result in serious

personal injury.

• Never try to read your watch when riding on a bicycle or when

operating a motorcycle or any other motor vehicle. Doing so is

dangerous and can result in a traffic accident and serious personal

injury.

• When you are wearing the watch, make sure that its auto light switch

is turned off before riding on a bicycle or operating a motorcycle or

any other motor vehicle. Sudden and unintended operation of the auto

light switch can create a distraction, which can result in a traffic

accident and serious personal injury.

TIMEKEEPING FUNCTION

In addition to time and date settings, the

Timekeeping Mode also lets you adjust the

Day of week

contrast of the display. Timekeeping Mode time

Month – Day

Year

is linked with World Time Mode time, so be

sure to select the city code for your current

location before setting the time in the

A L M

A LT I

S I G

RECALL

Timekeeping Mode.

A-LIGHT

AUTO

A L

MANUAL

Setting the city code, time, and

date

1. In the Timekeeping Mode, press D until

PM indicator

Seconds

the Timekeeping screen appears.

Hour : Minutes

2. Hold down A until the seconds digits starts

to flash on the display. The seconds digits

flash because they are selected .

• At this time, the city code currently set for the Timekeeping Mode appears

in the upper part of the display in place of the day of the week.

3. Press C to change the selection in the following sequence.

Seconds

City Code

CNT

Day

• See "Adjusting the display contrast" for details on using the

setting.

4. While the seconds digits are selected (flashing), press D to reset the

and L to toggle between the 12-hour and 24-hour formats.

seconds to

• If you press D while the seconds count is in the range of 30 to 59, the

seconds are reset to

and 1 is added to the minutes. If the seconds

count is in the range of 00 to 29, the minutes count is unchanged.

• With the 12-hour format, the P (PM) indicator appears to the left of the hour

digits for times in the range of noon to 11:59 pm and the A (AM) indicator

appears to the left of the hour digits for times in the range of midnight to

11:59 am.

• The 24-hour format is indicated by 24 on the display. Times are shown in

the range of 00:00 to 23:59.

5. Press C until the city code is flashing on the display.

6. Use B and D to scroll through the city codes until you find the one you

want to set as your home city.

• D scrolls forward, while B scrolls back through the city codes. Holding

down either button scrolls through the city codes at high speed.

• See the "CITY CODE TABLE" for a complete list of available codes.

7. Press C until the hour digits are flashing on display.

8. Press D to increase the setting or B to decrease it. Holding down either

button changes the setting at high speed.

9. Repeat steps 7 and 8 to set the minutes, year, month, and day.

10. After you make the settings you want, press A to return to the

Timekeeping Mode (Timekeeping screen).

• The day of the week is automatically set in accordance with the date.

• The date can be set within the range of January 1, 1995 to December 31,

2039.

• Changing the Timekeeping Mode's city code also causes the time to

change to the current time in time zone where the city is located.

• If you do not operate any button for a few minutes while a selection is

flashing, the flashing stops and the watch goes back to the Timekeeping

Mode automatically.

• Holding down B while in the Timekeeping Mode (Timekeeping screen)

displays the currently selected city code in place of the day of the week.

Hour

Minutes

Month

Year

CNT

(contrast)

Switching between standard time and daylight saving

time

Daylight Saving Time (DST), which is also sometimes called "summer time,"

advances the time one hour, as is the custom in some areas during the

summer.

1. In the Timekeeping Mode, press D until

the Timekeeping screen appears.

A L M

A LT I

2. Hold down A until the seconds digits starts

S I G

RECALL

A-LIGHT

AUTO

A L

MANUAL

to flash on the display. The seconds digits

DST

flash because they are selected .

3. Press C until the city code is flashing on

the display.

4. Press L to toggle Daylight Saving Time on

(DST displayed) and off (DST not

DST indicator

displayed).

5. After you make the settings you want, press A to return to the

Timekeeping Mode (Timekeeping screen).

• The DST indicator appears on the display to indicate that daylight saving

time is turned on.

Adjusting the display contrast

1. In the Timekeeping Mode, press D until

Graphic area

the Timekeeping screen appears.

2. Hold down A until the seconds digits starts

to flash on the display. The seconds digits

A L M

A LT I

S I G

RECALL

flash because they are selected .

A-LIGHT

AUTO

A L

MANUAL

• At this time, dots appear in the graphic area

of the display to indicate the current contrast

setting. Every two dots represent one

contrast level.

3. Press C seven times until the

indicator appears on the display.

4. Pressing D makes the images on the display darker, while B makes

them lighter.

• Display contrast can be adjusted to one of six levels. Two dots in the

graphic area indicate the lightest contrast setting (Level 1), while 12 dots

indicates the darkest setting (Level 6).

5. After you make the settings you want, press A to return to the

Timekeeping Mode (Timekeeping screen).

BAROMETER FUNCTIONS

This watch uses a pressure sensor to measure air pressure. This sensor can

be calibrated.

Important!

The barometer that is built into this watch measures changes in air pressure,

which you can then apply to your own weather predictions. It is not intended

for use as a precision instrument in official weather prediction or reporting

applications.

Example barometer applications

• Before going mountain climbing, you can take readings to find out the

probable upcoming weather.

• You can predict the weather for golf or other outdoor activities.

About barometric measurements

The barometer automatically takes measurements every two hours (starting

from midnight), regardless of what mode you are in. Barometric pressure

measurements are also taken every five seconds for three minutes after you

display the Timekeeping Mode's Barometric pressure/Temperature screen.

The last measurement result, along with the current temperature is displayed

in the Barometric pressure/Temperature screen.

Understanding the barometer screen

1. Use C to enter the Timekeeping Mode.

2. Press D to display the Barometric Pressure/Temperature screen.

• If you do not press any button for 10 or 11 hours, the watch automatically

returns to the Timekeeping screen.

A L M

A LT I

S I G

RECALL

A-LIGHT

AUTO

A L

MANUAL

Temperature

˚C

(Barometric Pressure/Temperature)

1 The barometric pressure graph shows the barometric readings for the

past 26 hours. The flashing point on the right of the display is the point for

the last measurement.

2 Some countries call this unit hecto-pascal (hPa), while other countries call

it millibars (mb). It really makes no difference, because 1 hPa = 1 mb. In

this manual, we will refer to hPa/mb or hPa (mb).

1571-2

C N T

Barometric pressure graph

(Unit: 1 hPa/mb)

hPa

Last measurement

(updated every 2 hours)