Casio 2273 Benutzerhandbuch - Seite 4
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Siehe Casio 2273 herunter. Casio 2273 10 Seiten. Casio pathfinder spf40: user guide
Seite drucken
Countdown Mode Beeper Operations
The watch beeps at various times during a countdown to keep you informed
about the countdown status without looking at the display. The following
describes the types of beeper operations the watch performs during a
countdown.
Countdown End Beeper
The watch beeps each second of the final 10 seconds before a countdown
reaches zero, and at zero. The first five beeps (seconds 10 through 6) are
higher pitched than the final five beeps (seconds 5 through 1). The watch
emits a longer beep to signal when the countdown reaches zero.
Note
The countdown end beeper always sounds, regardless of the on/off status of
the progress beeper.
Progress Beeper
The term "progress beeper" actually includes two beepers: a reset time
beeper and a reset period progress beeper .
Note
The reset time beeper and reset period progress beeper sound only while the
progress beeper is turned on.
• Reset Time Beeper
The reset time beeper is similar to the countdown end beeper. When the
progress beeper is turned on, the watch beeps each second of the final 10
seconds before the countdown reaches the reset time.
• Reset Period Progress Beeper
The reset period is the portion of the countdown between the reset time and
zero. When the progress beeper is turned on, the watch emits fours short
beeps at the top of each minute during the reset period.
Example 1
Countdown Start Time: 10'00"
Reset Time: 5'00"
Progress Beeper: On
Start Time
Reset time
10'00"
Reset Time Beeper
Example 2
Countdown Start Time: 10'00"
Reset Time: 5'00"
Progress Beeper: Off
Start Time
Reset time
10'00"
To turn auto repeat/repeat and the progress beeper on and off
1. While in the Countdown Timer/Stopwatch
Mode, hold down A until the time setting
starts to flash, which indicates the setting
screen.
2. Make sure the setting screen shows a
countdown start time other than zero.
• The next step will not work if the
3. Press D twice to display the screen for
making auto repeat, repeat, and progress
beeper settings.
4. Each press of E cycles though the
available settings as shown below.
Auto repeat, Progress beeper on
Auto repeat, Progress beeper off
Repeat, Progress beeper on
Repeat, Progress beeper off
5. After making the setting you want, press A to exit the setting screen.
Note
Even if you turn the progress beeper off, the watch beeps every second for
the last 10 seconds before the end of a countdown is reached.
Reset Period
Reset Period Progress Beeper
5'00"
4'00"
3'00"
2'00"
1'00"
0'00"
Countdown End Beeper
5'00"
0'00"
Countdown End Beeper
countdown start time setting is zero. If it
is, use the procedure to change it to
another value (see "To set the
countdown start time and reset time").
Countdown/Stopwatch Graphics
Graphic indicators move in a counter-clockwise direction during countdown
timer operation and clockwise during stopwatch operation.
• The zero point for both the minute's indicator and the second's indicator is
the 12 o'clock position.
• The factory default setting is graphics turned off.
Countdown Graphics
• During a countdown operation, the graphic
Second's indicator
indicators move counter-clockwise.
• One revolution of the second's indicator
represents 10 seconds.
• The minute's indicator appears when the
countdown time is 10 minutes or less. The
minute's indicator advances one step with
each full revolution of the second's
indicator. One revolution of the minute's
indicator represents 10 minutes.
Minute's indicator
Stopwatch Graphics
• During a stopwatch elapsed time operation,
Second's indicator
the graphic indicators move clockwise.
• One revolution of the second's indicator
represents 10 seconds.
• The minute's indicator advances one step
with each full revolution of the second's
indicator. One revolution of the minute's
indicator represents 10 minutes.
Minute's indicator
To turn timer graphics on and off
1. In the Countdown Timer/Stopwatch Mode,
hold down A until the time setting starts to
flash, which indicates the setting screen.
2. Display the graphics on/off screen.
• If you started from the Countdown Timer
• If you started from the Stopwatch Mode,
3. Press E to toggle the graphic display on
(
4. After making the setting you want, press
A to exit the setting screen.
Using Countdown Timer
The following procedure is explained assuming the countdown timer is
configured with the following sample settings.
Progress beeper: On
Countdown Start Time: 10 minutes
Reset Time: 5 minutes
To use the countdown timer
In the Countdown Timer/Stopwatch Mode,
press E to start the countdown timer.
• The indicator YACHT flashes on the display
while a countdown operation is in progress.
• The countdown proceeds in accordance
with the configuration settings you made
using the procedures under "Configuring the
Countdown Timer".
The table below describes the button operations you can perform while a
countdown operation is in progress.
To do this:
Stop the countdown operation
Display the reset time (5 minutes in
this example)
Display the countdown start time
The following describes the operations you can perform while the countdown
operation is stopped (by pressing E).
To do this:
Resume the countdown from the
currently displayed time
Display the countdown start time (10
minutes in this example)
Mode, press D three times.
press D once.
ON
displayed) and off (
OFF
displayed).
Do this:
Press E.
Press A.
• Pressing E after displaying the reset
time starts the countdown from the
displayed time.
Press A and E at the same time, or
press A twice.
Do this:
Press E.
Press A and E at the same time or
press A.
• Pressing E after displaying the
countdown start time starts the
countdown from the displayed time.
2273-4