Casio 2347 Allgemeines Handbuch - Seite 4

Blättern Sie online oder laden Sie pdf Allgemeines Handbuch für Siehe Casio 2347 herunter. Casio 2347 6 Seiten. Watch

Casio 2347 Allgemeines Handbuch
MEMORY
The watch is equipped with memory that you can use to store up to 10
barometric pressure and temperature readings. Note that the date and time of
the measurement is not included with the data. The number of available blank
records that can be used to store data is shown on the right side of the
Barometer and Thermometer Mode screens.
Storing a Measurement
While in the Barometer or Thermometer Mode, hold down D for about one
second until the watch beeps, indicating that the latest measurement is stored
in memory.
• The message "FULL" appears on the display for about one second when
you hold down D while memory is full. No more data can be stored while
memory is full.
• If you want to store more data after memory becomes full, use the
procedure under "Recall Mode" below to delete the current data to make
room for new data.

RECALL MODE

Recalling data
1. Use C to enter the Recall Mode.
2. Each press of D cycles through the barometric pressure and temperature
data in memory. Mode indicators appear to tell you what type of data is
currently displayed.
• Note that measurement units are not indicated on the Recall Mode screens.
• The display shows "- - - - – –" if there is no data.
1 second
A
B
later
C
D
Recall Mode indicator
Deleting Data
While in the Recall Mode, hold down A. The
A
watch beeps, and the message CLR flashes
on the display to indicate data is about to be
deleted. Keep A depressed for about two
seconds to delete all the measurement data
currently in memory.
• Note that this procedure deletes all
measurement data in memory. You cannot
delete individual records.

ALARM MODE

When the Daily Alarm is turned on, the alarm sounds for 20 seconds at the
preset time each day. Press any button to stop the alarm after it starts to
sound.
When the Hourly Time Signal is turned on, the watch beeps every hour on the
hour.
A
B
C
D
Alarm Mode indicator
To set the alarm time
1. Hold down A until the hour digits start to flash on the display. The hour
digits flash because they are selected . At this time the alarm is
automatically turned on.
2. Press C to change the selection in the sequence shown below.
Hour
3. Press D to increase the number or B to decrease it.
• Holding down either button changes the setting at high speed.
4. After you set the alarm time, press A to return to the Alarm Mode screen.
• The format (12-hour and 24-hour) of the alarm time matches the format you
select for normal timekeeping.
• When setting the alarm time using the 12-hour format, take care to set the
time correctly as morning or afternoon.
Memory number
Barometric pressure
Alarm time
1 second
later
Hourly Time Signal on
indicator
Daily Alarm on indicator
Minutes
To stop the alarm
• Press any button to stop the alarm after it starts to sound.
To turn the Daily Alarm and Hourly Time Signal on
and off
Press D while in the Alarm Mode to change the status of the Daily Alarm and
Hourly Time Signal in the sequence shown below.
Both OFF
Both ON
• The Daily Alarm and Hourly Time Signal on indicator is displayed in all
modes.
To test the alarm
Hold down D while in the Alarm Mode to sound the alarm.
• Note that pressing D also changes the Daily Alarm and Hourly Time Signal
on and off settings.
COUNTDOWN ALARM MODE
The countdown alarm can be set within a range of 10 seconds to 60 minutes.
When the countdown reaches zero, an alarm sounds for 10 seconds or until
you press any button.
About Auto-repeat
• When the end of the countdown is reached while Auto-repeat is on, the
alarm sounds, but the countdown restarts from the beginning without
stopping.
• To stop the countdown, press D. You can then manually reset to the start
time by pressing B.
• If you set a starting time of 1 minute or less and have Auto-repeat turned
on, the countdown alarm tone (which normally sounds for 10 seconds)
sounds for only one second.
About the Progress Beeper
• When the Progress Beeper is turned on, the watch beeps as the countdown
time passes the 10, 5, 4, 3, 2, and 1-minute marks, and the 50, 40, 30, 20,
10, 5, 4, 3, 2, and 1-second marks.
• Even if the Progress Beeper is turned on, it does not operate if you set a
starting time of 1 minute or less and have Auto-repeat turned on.
A
B
C
D
Countdown Alarm Mode indicator
To make countdown alarm settings
1. Hold down A while in the Countdown Alarm Mode. The minites setting
flashes on the display because they are selected .
2. Press C to change the selection in the following sequence.
Minutes
Seconds
3. Press D to increase the selected number or B to decrease it. Holding
down either button changes the setting at high speed.
• The seconds can be set in units of 10 seconds.
• Set 0 minutes, 0 seconds to specify a start time of 60 minutes.
• While the Progress Beeper ON/OFF setting is selected (flashing), press D
or B to toggle the Progress Beeper on and off.
• While the Auto-repeat ON/OFF setting is selected (flashing), press D or B
to toggle Auto-repeat on and off.
2345/2347-4
Hourly Time
Daily Alarm only
Signal only
1 second
later
1/10 second
Seconds
Minutes
Progress beeper
Auto-repeat
BEEP ON/OFF
AUTO ON/OFF