Casio 2730 Betriebshandbuch - Seite 7

Blättern Sie online oder laden Sie pdf Betriebshandbuch für Siehe Casio 2730 herunter. Casio 2730 10 Seiten.

Seite drucken

Alarm Mode

Using the Alarms

Alarm Mode

You can use the Alarm Mode to configure settings for various

types of alarms (daily alarm, snooze alarm, target alarm) or for the

hourly time signal.

This watch has five alarms: three daily alarms, one target alarm,

and one snooze alarm.

• Daily Alarm (AL1, AL2, AL3)

With a daily alarm, the watch beeps for 10 seconds when the

alarm time is reached.

• Target Alarm (TAL)

With a target alarm, the time remaining until the alarm time

counts down on the display.

• The watch beeps for 10 seconds when the alarm time is

reached.

• Snooze Alarm (SNZ)

With the snooze alarm, the watch beeps for 10 seconds when

the alarm time is reached, and up to seven times at five-

minute intervals thereafter. Pressing any button stops the

beeper, but the alarm will sound again after five minutes.

Turning an Alarm Time On and Off

In the Alarm Mode, use the D button to display the screen for the

alarm you want to turn on or off.

Press the A

A button to toggle the displayed alarm on or off.

• Turning on an alarm causes the alarm indicator (ALM) to appear

on its screen. The snooze alarm screen also has a snooze

indicator (SNZ).

Alarm 1 Screen

Snooze Alarm Screen

Alarm Indicator

Snooze Indicator

Operation Guide 2730

Viewing the Alarm Time or Target Alarm

Time

Alarm Name

Indicator

In the Alarm Mode, press the

D button to cycle through the

alarm screens in the sequence

shown below.

• The alarm name indicator

appears first, followed by the

current alarm time setting.

Alarm Time

Alarm 1

Alarm 2

Alarm 3

(AL1)

(AL2)

(AL3)

Hourly Time

Snooze

Target

Signal (SIG)

Alarm (SNZ)

Alarm (TAL)

• About the Target Alarm Time Screen

If the target alarm (TAL) is turned

on, the alarm time appears first,

followed by a screen that shows

how much time remains until the

alarm time is reached (target

time).

Target Time

Stopping the Alarm Beeper

Pressing any button while the beeper is sounding stops it.

• In the case of the snooze alarm the alarm will sound again. The

snooze indicator flashes while the snooze alarm is active

(indicating that the alarm will sound again).

• Use the procedure under "Turning an Alarm Time On and Off" to

turn off the snooze alarm so it does not sound any more.

Important!

Performing any of the following operations while the snooze

indicator is flashing on the display cancels the snooze operation

and stops the flashing.

• Displaying the Timekeeping Mode setting screen

• Displaying the Alarm Mode (snooze alarm) setting screen

Testing the Alarm

In the Alarm Mode, hold down the D button to sound the alarm.

Setting an Alarm Time

In the Alarm Mode, use the

D button to display the

screen for the alarm

whose time you want to

set.

A button

Hold down the A

Hour

for about two seconds

until the hour digits of the

alarm time start to flash.

• This is the setting screen.

Displaying the setting

automatically turns on the

alarm.

Alarm Indicator

Use the D

D (+) and B

B (–)

buttons to change the

hour setting.

• Holding down either button

scrolls at high speed.

• When setting the hour, make

sure you specify AM (no

indicator) or PM (P) correctly

when using 12-hour

timekeeping, or that you

specify the correct 24-hour

time.

• The same 12-hour/24-hour format you select for the

Timekeeping Mode time is also applied in the Alarm Mode.

Using the Hourly Time Signal

The hourly time signal causes the watch to beep every hour on

the hour.

Turning the Hourly Time Signal On and Off

In the Alarm Mode, use the D button to display the screen for

the hourly time signal (SIG).

Press the A

A button to toggle the hourly time signal on or off.

• Turning on the hourly time signal causes its indicator (SIG) to

appear on the screen.

Hourly Time Signal Screen

Hourly Time

Signal Indicator

Press the C

C button to

move the flashing to the

minute digits.

• As with the hour setting, use the

D (+) and B (–) buttons to

change the minute setting.

• Each press of C moves the

flashing between the hour

digits and the minute digits as

shown below.

Hour

Minutes

When the alarm time is the way you want, press the A

button.

(Back)

• This exits the setting screen.

• The display also will exit the setting screen automatically if

you do not perform any operation for about two or three

minutes.

(Forward)

Minutes

(Back)

(Forward)