Danfoss TS715 Si Betriebsanleitung

Blättern Sie online oder laden Sie pdf Betriebsanleitung für Thermostat Danfoss TS715 Si herunter. Danfoss TS715 Si 2 Seiten. Underfloor heatig timeclock
Auch für Danfoss TS715 Si: Gebrauchsanweisung (2 seiten)

Seite drucken
Danfoss TS715 Si Betriebsanleitung
+1HR
ON
12:00
OFF
AUTO
PM
ALL DAY
MO
MAN
PROG
+
DAY
SELECT
NEXT ON/OFF
COPY
–
Programming – day and time
1.
Open the cover. Press
prog
programming mode.
SET
TIME
+1HR
12:00
PM
MO
MAN
PROG
+
DAY
SELECT
NEXT ON/OFF
COPY
–
Programming –
on/off times
4.
Press
to enter
prog
on/off
programming mode.
SET
OFF
TIME
+1HR
11:15
6
PM
MO
MAN
PROG
+
DAY
SELECT
NEXT ON/OFF
COPY
–
8.
Press
and repeat steps 5 – 7
next
until all
times are
on/off
programmed to suit.
9.
If unit is pre-set for 24 hour operation
go to step 13, If a different cycle is
required, alter the internal pins and
continue with step 10 (see opposite).
6
Systems with dial thermostats
Operating instructions for the underfloor heating timeclocks
TS715 – Single-channel timeclock
Nu-Heat supplies Danfoss TS715 single-channel programmable floor heating
timeclocks to control the underfloor heating system.
Room zone temperatures are individually controlled by simple dial-type thermostats.
Please remember that underfloor heating takes longer to warm up and cool down
than conventional radiators and the timeclock settings should reflect this.
Ensure that each timeclock is set to your requirements as follows:-
+1HR
MAN
SELECT
R/S
to enter
2.
Press
day
Repeat until correct day is displayed.
+1HR
MAN
SELECT
R/S
5.
Use
+
or
(setting number 1).
+1HR
MAN
SELECT
R/S
10.
Press
day
if different programming from the
previous day is required.
If the programme is the same, go
to step 11.
SET
TIME
12:00
PM
TU
PROG
+
DAY
NEXT ON/OFF
COPY
–
R/S
to select day of the week.
SET
ON
TIME
4:30
AM
1
MO
PROG
+
DAY
NEXT ON/OFF
COPY
–
R/S
-
to adjust the 1st
time,
on
SET
OFF
TIME
12:30
4
PM
TU
PROG
+
DAY
NEXT ON/OFF
COPY
–
R/S
to advance to the next day
continued
+1HR
SET
TIME
12:02
PM
MO
MAN
PROG
+
DAY
SELECT
NEXT ON/OFF
COPY
–
3.
Use
+
or
-
to adjust the time until
correct.
+1HR
SET
OFF
TIME
8:00
AM
2
MO
MAN
PROG
+
DAY
SELECT
NEXT ON/OFF
COPY
–
6.
Press
to step to 1st
next
(setting number 2).
7.
Use
+
or
-
to adjust the 1st
(setting number 2).
SET
OFF
TIME
+1HR
11:15
6
PM
FR
MAN
PROG
+
DAY
SELECT
NEXT ON/OFF
COPY
–
11.
Press the
button to copy the
copy
previous day's programming to the
current day.
12.
Repeat steps 10 – 11 until all days
are programmed.
13.
Press
to return to
prog
R/S
R/S
time,
off
time,
off
R/S
mode.
run