Danfoss FCM 300 Series Schnelles Einrichten - Seite 2

Blättern Sie online oder laden Sie pdf Schnelles Einrichten für Medienkonverter Danfoss FCM 300 Series herunter. Danfoss FCM 300 Series 2 Seiten.
Auch für Danfoss FCM 300 Series: Schnelles Einrichten (5 seiten), Schnelles Einrichten (2 seiten)

Seite drucken

Danfoss FCM 300 Series Schnelles Einrichten

Factory setting

Reset (pushbutton)

Start

Jog

Speed reference

- Reset to be closed short time for

resetting fault trips

- Start to be closed for changing

to run mode

- Jog will run at fixed speed

while closed (10 Hz)

- Speed reference (0-10 V)

determines speed while in run mode

Fig. 1

The control cables must be screened cables.

Fig. 2

X100: Terminal block for data communication

Terminal

Function

No.

P RS 485

for connection to

N RS 485

bus or PC

5 V DC

Supply for RS 485 bus

0 V DC

T T T T T able A

able A

X101: Terminal block for analog/digital control signals

Terminal

Function

No.

Analog input (0-20 mA)

Analog (0-10 V)/digital input 2

Digital input (or pulse) 3

Digital input (or precise stop) 4

Digital input (other) 5

24 V DC supply for digital inputs (max. 50 mA)

10 V DC supply for potentiometer (max. 15 mA)

0 V for terminals 1-7 and 9

Analog (0-20 mA)/digital output

T T T T T able B

able B

02/00

VLT T T T T

This Quick Setup gives information on safety and

helps you to get your FCM 300 Series motors

installed and running in factory setting, see fig. 1. For

additional information, please see the Design Guide.

Before you start, please read the safety instructions

on the back of this Quick Setup.

Mechanical installation

Terminals

Install the FC motor with adequate access for routine

1: Analogue input

maintenance. Adequate space, particularly at the fan

inlet (50 mm), is necessary to facilitate airflow.

2: Analogue input

3: Digital input

Where several FC motors are installed in close

4: Digital input

proximity, care must be taken to ensure that there is

5: Digital input

no recirculation of exhausted warm air.

6: 24 V DC supply

NB!

7: 10 V DC supply

8: 0 V

9: Output

to exceed 35 °C. If the ambient temperature is in the

range of 40 °C - 55 °C, a reduction of the service life

of the FC part is to be expected. For further

information, please see the section on derating in the

Design Guide.

Electrical connections

Remove the inverter box cover, which is held by four

screws, to obtain access to the terminals.

Remove the detachable terminal plugs from the

terminal blocks X100 and X101 to obtain access to

the mains terminals.

Lift only the corner of the black plastic cover by the

cable entries to expose the mains terminals L

and L

NB!

Do not lift or remove the entire plastic cover. The

NB!

Mains terminals L

Connect the three mains phases to terminals L

and L

provided.

T T T T T ightening T

ightening Tor or or or orques

ightening T

L1, L2, L3

Earth ground FCM 305-375

Example

Another direction of rotation can be programmed,

see the Design Guide.

Feedback

signal

Speed

reference

Start the FC motor

Reset

Connect mains. LED 302 (green) lights up to indicate

Start

that the power is on. In Profibus versions, LED 303

Jog (fixed

will flash. For further information on Profibus, please

speed)

see the Profibus manual.

Connect terminal 4 and 6 to the start button (see fig.

1).

Fault

Connect terminal 2, 7 and 8 to the potentiometer

indication

(see fig. 1).

Mount the inverter box cover.

Fastening torque: 2.2 - 2.4 Nm

MG.03.F4.02 - VLT is a registered Danfoss trademark

® ® ® ® ®

DriveMotor FCM 300 Quick Setup

Ambient temperature

To avoid the FC part getting overheated, the

ambient temperature is not to exceed 40 °C

and the 24-hour average temperature is not

(see fig. 2).

voltage on the FC motor is dangerous

and may lead to material damage,

serious injury or it may be fatal.

and L

Make sure that your mains supply

corresponds to the voltage required by the

FC motor (see inverter label), TT and NT

mains .

and the earth to the separate terminal

ques

FCM 305-340

0,5-0,6 Nm

FCM 355-375

1,2-1,5 Nm

3,4 Nm

N N N N N B! B! B! B! B!

You cannot change the rotation direction of

the motor by shifting around the phases. The

direction of rotation is clockwise by default.

T T T T T ools for installation

ools for installation

1 cross-point screwdriver

1 large screwdriver

1 small screwdriver

Min. 2 glands:

Gland sizes

FCM 305-330

FCM 340-375

1 mains cable

1 control cable

Max. cable cross section

Mains supply cable

Control cable

Serial communication cable

NB!

Bearings

Ball and roller bearings are despatched from the

works fully charged with grease. Shielded bearings

have sufficient grease for an operating life of at least two

years in normal ambient temperatures, providing there is

little or no leakage.

Tapping of fitments onto the motor shaft,

with a hammer or mallet, causes bearing

damage. This results in increased bearing

noise and a significant reduction in bearing

life.

Pr Pr Pr Pr Prefuses Max.

efuses Max.

FCM 305-322

10A

FCM 330-340

15A

FCM 355-375

25A

IEC

FCM 305-375

25A

, L

Type gG prefuses must be used. If you want to maintain

UL/cUL you must use prefuses of the type Bussmann

KTS-R 500 V or Ferraz Shawmut, type ATMR (max. 30A). The

fuses must be placed for protection in a circuit that is capable of

supplying a maximum of 100,000 amps RMS (symmetrical), 500

V maximum.

Contr

ol terminals

Contr

Control terminals

ol terminals

For information on terminal blocks X100 and X101, please

see table A and B.

RS 485 switch

For terminating an RS 485 interface serial communication,

the bus must be terminated by a resistor network at both

ends. This is provided by setting both switches to ON.

LEDs

The FC motor has five LEDs which indicate the status of

the FC motor:

LED 300 (red):

LED 301 (yellow):

LED 302 (green):

LED 303-304 (green):

EMC-corr

EMC-correct installation

EMC-corr

ect installation

EMC-corr

ect installation

The control cables must be screened cables to ensure

EMC-correct electrical installation.

Connect the screen to earth at both ends.

Avoid installation with twisted screen ends (pigtails), since

this ruins the screening effect at high frequencies. Use

cable clamps instead.

Use the start button to start the FC motor and adjust the

speed by means of the potentiometer.

The voltage on the FC motor is

dangerous when the motor is connected

to mains. Incorrect installation of the FC

motor may lead to material damage or

serious injury or it may be fatal.

175R0129

3X PG16

1X PG21, 2X PG16

4.0 mm

/10 AWG

1.5 mm

/16 AWG

1.5 mm

/16 AWG

Fault trip

Warning

Power on

Communication