Danfoss VLT AutomationDrive FC 302 Installationsanleitung Handbuch

Blättern Sie online oder laden Sie pdf Installationsanleitung Handbuch für Medienkonverter Danfoss VLT AutomationDrive FC 302 herunter. Danfoss VLT AutomationDrive FC 302 6 Seiten. Igbt module replacement for d1h–d8h drives
Auch für Danfoss VLT AutomationDrive FC 302: Betriebshandbuch (16 seiten), Installationshandbuch (20 seiten), Einbauanleitung (4 seiten), Installationsanleitung Handbuch (6 seiten), Installationsanleitung Handbuch (12 seiten), Installationshandbuch (18 seiten), Installationsanleitung Handbuch (8 seiten), Installationsanleitung Handbuch (10 seiten), Installationshandbuch (6 seiten), Installationshandbuch (16 seiten), Betriebsanleitung (16 seiten), Installationsanleitung Handbuch (6 seiten), Installationshandbuch (16 seiten), Installationshandbuch (8 seiten), Installationshandbuch (6 seiten)

Seite drucken
Danfoss VLT AutomationDrive FC 302 Installationsanleitung Handbuch
Installation Instructions
®
VLT
Wireless Communication Panel LCP 103
®
VLT
FC Series FC 102, FC 103, FC 202,
FC 301/FC 302, and LD 302
Items Supplied
•
®
VLT
Wireless Communication Panel LCP 103.
•
Gasket
®
Illustration 1.1 VLT
Wireless Communication Panel LCP 103
Compatible Drive Series
NOTICE
Compatible drives have a white USB port.
•
®
VLT
HVAC Drive FC 102
•
®
VLT
Refrigeration Drive FC 103
®
•
VLT
AQUA Drive FC 202
•
®
VLT
AutomationDrive FC 301/FC 302
•
®
VLT
Lift Drive LD 302
Compatible software versions
-
FC 102: 5.10
-
FC 103: 2.10
-
FC 202: 3.10
-
FC 30x: 8.03
Approvals and Certifications
NOTICE
FCC COMPLIANCE NOTICE
This equipment has been tested and found to comply with
the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by 1 or more
of the following measures:
•
•
•
•
Modifications: Any modifications made to this device that
are not approved by Danfoss may void the authority
granted to the user by the FCC to operate this equipment.
RF EXPOSURE COMPLIANCE
This portable transmitter with its antenna has shown
compliance with FCC's SAR limits for general population/
uncontrolled exposure. The maximum listed SAR level is 0.22
W/kg (body). The antenna used for this device must not be
co-located or operating in conjunction with any other
antenna or transmitter.
Danfoss A/S © 08/2018 All rights reserved.
FCC ID: 2ANSELCP-103
Reorient or relocate the receiving antenna.
Increase the separation between the equipment
and receiver.
Connect the equipment into an outlet on a circuit
different from that to which thereceiver is
connected.
Consult the dealer or an experienced radio/
television technician for help.
MI38V402