FreeAir SU-27 Flanker Montageanleitung

Blättern Sie online oder laden Sie pdf Montageanleitung für Spielzeug FreeAir SU-27 Flanker herunter. FreeAir SU-27 Flanker 4 Seiten.

Seite drucken

Dear customer,

congratulations on your purchase of our model of the famous Su-27 Flanker fighter. Before commencing its building, please study

the assembly instructions carefully and make sure you understand the building process. If need be, contact the manufacturer or your

dealer

Name of part

Fuselage of EPP

Elevator control rod

Wing of EPP

Elevator of EPP

Vertical tail of EPP

Engine nacelle

Elevator shaft bushing

Jet pipe of EPP

Motor bulkhead

Engine nacelle upper part of EPP

You will need also the:

CyA glue, CyA glue activator, sharp (modelling) knife, 150 mm extension cable. To complete the model you will need: a receiver

(MZK), servos (Wipont W-060), a controller (TMM-1210-3 or Jeti 12), an accumulator battery (3 LiPol cells of 640-1200 mAh), a

motor (HCS-80/2E or similar of about 80 W output).

Description of the model:|

The model is completely made of EPP and has some carbon components. With its weight beginning at 250 grams it is an ideal

model for flying in any suitable spot (e.g. a school playground or in the street). It is intended not only for experienced pilots, but also

for the advanced modellers. To power it you may use a motor from our production, e.g. the HCS-80/2E, and three Lithium Polymer

cells. Thanks to a well thought-out design the construction would take only about 90 minutes.

Building process:

Unless otherwise stated, all joints should be glued with the rapid CyA glue. Start the building by assembling the engine

nacelles (Fig. 1). Using the Fig. 2 as a guide, glue in place the bushings for the slab elevator. Insert the carbon tube

through the location grooves and slide onto it the elevator lever, then the two securing rings, two from each side,

respectively (Fig. 3).

Move the securing rings to their extreme external positions to eliminate any play in the carbon tube. Then carefully

glue the rings, ensuring at the same time the freedom of movement of the carbon tube.

Glue the elevator servo in place and install the elevator control rods. Pierce/drill a hole through a cube of EPP and slide

it onto the control rod, to serve as the control rod guide. Check the neutral position of the servo and glue the elevator

lever in place (Fig. 4).

Repeat the process for the other engine nacelle; keep in mind the nacelles are right and left.

Now glue the wings to the fuselage central part, and, using a sharp modelling knife, cut a 1-2 mm deep slit into the

wing from both upper and lower side. Press the carbon spar (rod) into the slit and glue there from both sides, using thin

CyA glue (Fig. 5). Work on a flat surface to ensure the complete assembly is not distorted. Check the quality of the

wing reinforcement and glue the fuselage in place (Fig. 6).

Glue the engine nacelles to the fuselage (Fig. 7).

Check the elevator shafts of carbon are coaxial and glue the vertical tail surfaces in place (Fig. 8).

Glue the elevator halves (Fig. 9). Ensure the wing and right and left elevator planes are parallel and that they are at the

same angle relative to the wings.

Using the Fig. 10 as a guide, glue the motor bulkhead, screw-on the motor bearers (Fig. 11) and secure the motor in

place.

Install the speed controller as per Fig. 12. The position of the controller is shown on the Fig. 13. Using a hand-held

soldering gun, cut a hole for the receiver into the fuselage. If the controller's servo cable is long enough, there is no

need to use an extension one. Connect cable extensions to the power cables of the controller, or cut the original cables

short and splice them with new cables of the same thickness, and of the necessary length. Glue the engine nacelle upper

part in place (Fig. 14). Now glue the EPP jet pipes to the engine nacelles (Fig. 15) and the doubler of the fuselage

motor section.

The model is now ready for balancing. By shifting the propulsion batteries, set the position of the centre of

gravity to some 320 mm from the motor bulkhead. Then, using a soldering gun, cut an opening for the battery pack; the

dimensions of the battery opening shall be some 2 to 3 mm less than the outer dimensions of the battery pack, to ensure

that the batteries would hold in place without any extra fixation.

Now the model is complete, you can enhance its appearance by applying the marking self-adhesive decals. For

the first flight, set the deflection of the controls to the half of their travel.

Stavební návod SU-27 Flanker

SU-27 Flanker

List of parts:

piece

Name of part

Elevator securing ring

Elevator shaft (carbon 5x100 mm)

Elevator lever

Carbon undercarriage

Aileron control rod lever

Wing spars (carbon 500x1 mm)

Fuselage central part of EPP

Instructions

Self adhesive decal set

Doubler of the fuselage motor

section (Al 1,6x100 mm)

www.freeair.cz

pieces

Strana .: 1 / 4