Addlogix KVM-801PREU-OSD Handbuch zur Schnellinstallation

Blättern Sie online oder laden Sie pdf Handbuch zur Schnellinstallation für Schalter Addlogix KVM-801PREU-OSD herunter. Addlogix KVM-801PREU-OSD 2 Seiten. Powerreach elite hd. 8/16-port cascadable rackmount usb ps/2 kvm switch w/ osd

Seite drucken

Firmware-Upgradeable

User-definable Hotkey-preceding

Sequence

Addlogix

PowerReach

KVM-801PREU-OSD / KVM-1601PREU-OSD

8/16-port Cascadable Rackmount

USB PS/2 KVM Switch w/ OSD

Quick Installation Guide

Thank you for purchasing the Addlogix KVM-801PREU-OSD /

KVM-1601PREU-OSD Cascadable Rackmount USB PS/2 KVM

Switch. With our high quality product, users can enjoy countless

benefits from using it.

Out-of-the-box Installation

Take the KVM Switch out of the box and begin

installation...

If you are using any PS/2 computer: Please make sure

all of your PS/2 computers are powered off before connecting to

the KVM Switch. Otherwise, the KVM Switch system might not be

properly set up. However, USB computers do not have this

limitation.

Step 1.

Make sure (at least the PS/2) computers that are to be

connected to the KVM switch are powered off. If not,

power them off before you proceed with the following

steps.

Step 2.

Connect the shared keyboard, mouse and monitor to the

console connectors on the rear of your (master) KVM

switch. Power on the KVM Switch by attaching the

power adapter cord.

Although the power is constantly fed through the USB or PS/2

interface from the connected computer, it is still necessary to use

the external power adapter for more stable OSD operation and the

cascaded application. Without external power source, the stability

of the KVM system might be compromised.

If you use only a single KVM switch in non-cascaded

application, you should ignore step 3, 4 and 5 and jump directly to

step 5.

If you want to daisy-chain multiple KVM Switches, go to

step 3. You can daisy-chain up to 16 levels of KVM Switches with a

maximum of 256 computers connected.

Step 3. Use the daisy-chain cable (M-HDB15-HDB15-F) to

connect the DaisyChain OUT Port (HDB 15 female) of

the master KVM Switch to the DaisyChain IN Port (HDB

15 male) of the second KVM switch. Connect the power

adapter cord to the second switch to power it on.

Step 4. If you have yet another switch to be daisy-chained, just

repeat Step 3 to connect them. You can daisy-chain up

No Terminator required if only using a single unit.

Step 5. (Now your KVM switch or daisy-chained KVM Switches

Elite HD

The special KVM cable provides a PS/2 keyboard connector, a

USB connector and a HDB video connector for the computer

connection. When connecting with a USB computer, just plug the

USB connector to it and leave the PS/2 connector free. When

connecting with a PS/2 computer, just add one USB-to-PS/2

adapter to the USB connector and you'll have a PS/2 connector for

mouse. Do not connect USB connector and PS/2 keyboard

connector to a computer at the same time.

Step 6. Power up the connected computers. After your computer is

powered up the keyboard and mouse will be recognized

and now you can begin operating the switch.

Easy Operation

There are three ways to select a specific computer (on a specific

switch, if you have multiple daisy-chained KVM switches), using

front-panel push button, hotkey sequence or OSD Menu.

to 16 units of KVM switches. Plug a terminator onto

the Daisy-chain Out Port of the last KVM switch unit.

should have been powered-up and initialized). Connect

each of your computers to a computer port on the rear of

the switch(es). You should use the special USB PS/2

KVM

cable

(with

the

USB-to-PS/2

connection to a USB computer (PS/2 computer).

Front-panel push buttons

The front-panel buttons let you have direct control over KVM

switch operation and channel switching. Simply press a button to

switch to its corresponding channel.

Keyboard hotkeys

A keyboard hotkey sequence consists of at least three specific

keystrokes:

See Quick Reference Sheet

Hotkey sequence = ScrLk + ScrLk + Command key(s)

adapter)

for

The two consecutive ScrLk keystrokes should be pressed

within 2 seconds and the following command key(s) should also be

pressed within 2 seconds in likewise manner. Otherwise, the

hotkey sequence will not be validated.

For detailed Hotkey sequences and their corresponding

functional commands.

OSD Menu

To activate the OSD (On Screen Display) Menu, use the hotkey

sequence:

Activate OSD

Deactivate OSD

Main OSD Menu

Main menu

Select

computer:

PgUp/PgDn to scroll page. Hit Enter to select.

Edit computer name: just hit Insert to edit and Enter to confirm.

F1 : Next Page - rotate through Main Page / Setup page / Status

page

F10: Logout - lock your keyboard and mouse for security.

Password will be needed to log in.

Setup Menu

Autologout: specify time for auto logout (00~99 min)

OSD timeout: specify duration for OSD menu to stay on screen

Autoscan period: specify time for autoscan period

Title bar: enalble/disable the title bar, and also specify its position

Hotkey: specify the hotkey preceding sequence (SCROLL LOCK,

CAPS, ESC, F12 or NUM LOCK)

Setup Password: specify the password for access

Load Default: load default settings

Load Default All: load default settings to all daisy-chained units

Upgrade Firmware: upgrade the firmware of the KVM switch

Firmware Upgrade

This KVM Switch allows its user to upgrade firmware contents

whenever is needed to enhance the compatibility to other devices

or its functions and performance. Use the firmware upgrade cable

for connection to a host PC via the "Daisy-chain IN" port (see

previous configuration diagram). For firmware upgrade procedure,

please refer to Firmware Upgrade Operation Guide.

See Quick Reference Sheet

= ScrLk + ScrLk + Space Bar

= ESC (Escape key)

Setup Menu

Up/Down

use

Arrow

key

navigate,