SYNCHRO/ENDING
NORMAL/FILL-IN
Recording Chords with Step Record-
ing
With step recording, you can record a chord progression in Track 1
chord-by-chord. You can then use the chord progression as an Auto
Accompaniment or later add melody notes to Track 2.
To record chords to Track 1 using step recording
1.
Use the MEMORY button to enter record standby, and
then use [+] and [–] to select 0 or 1 as the song num-
ber.
R
c e
2.
Press the LEFT/TRACK 1 button to select Track 1.
3.
Press the STEP button.
Flash
4.
Make any of the following settings if you want.
• Rhythm number (page E-16)
• MODE switch (page E-16)
5.
Press the SYNCHRO/ENDING button.
6.
Play a chord.
• Use the chord play method that is specified by the current
MODE switch setting: FINGERED, CASIO CHORD, NOR-
MAL.
• When the MODE switch is set to NORMAL, specify the chord
using the root input keyboard and chord type input key-
board. See "Specifying Chords in the Normal Mode" on this
page for details.
Measure number
Chord name
Clock
number*
Flash
* 48 clocks = 1beat
E-28
FF
INTRO
REW
TOUCH
ACCOMP
KEY LIGHT
RESPONSE
VOLUME
TOUCH
RESPONSE
KEY LIGHT
METRONOME BEAT
TEMPO
MODE
VOLUME
SYNCHRO/
INTRO
ENDING
POWER
MAX
FULL RANGE
CHORD
FINGERED
START/
STOP
CASIO CHORD
NORMAL
MIN
NORMAL/
VARIATION/
SONG BANK CONTROLLER
FILL-IN
FILL-IN
MODE
START/STOP
VARIATION/FILL-IN
.
N .
o
1
GM
MEMORY
STEP
Beat number
LEFT/TRACK 1
RIGHT/TRACK 2
TRANSPOSE/
GM
TUNE/MIDI
MEMORY
STEP
MEMORY
STEP
SPLIT
LAYER
(TIE)
7
8
9
Number buttons
4
5
6
DEMO
3-STEP LESSON
1
2
3
REST
0
STEP 1
STEP 2
STEP 3
[+]/[–]
STEP
MEMORY
7.
Input the length of the chord (how long it should be
played until the next chord is played).
• Use the number keys to specify the length of a chord. See
"Specifying the Length of a Note" on page E-29 for details.
• Repeat steps 6 and 7 to input all the chords you want.
• If you make a mistake while step recording chords, use the
procedure under "Editing Data While Step Recording" to
make corrections.
8.
After you finish step recording, press the START/STOP,
MEMORY, or STEP button.
• This enters playback standby for the song you have just in-
put. Pressing the START/STOP button plays it back.
NOTES
• You can use the FF and REW buttons to change the current input posi-
tion during step recording. See "Editing Data While Step Recording" on
page E-30 for details.
• Pressing the [0] button in step 7 inputs a rest. Note, however, that any
rests you input do not have any effect on Auto Accompaniment.
Track 1 Contents After Step Recording
In addition to chords, the following data is also recorded to Track 1
during step recording.
• Tone number
• Rhythm number (step 4)
• INTRO, SYNCHRO/ENDING, NORMAL/FILL-IN, VARIATION/
FILL-IN button operations (step 6)
Specifying Chords in the Normal Mode
When the MODE switch is set to NORMAL during step recording,
you can specify chords using a method that is different from CASIO
Chord and Fingered fingerings. This chord specification method can
be used to input 18 different chord types using only two keyboard
keys, so chords can be specified even if you don't know how to actu-
ally play them.
Root input keyboard
1 1 1 1 1 Major
0 0 0 0 0 Seventh flat five
2 2 2 2 2 Minor
A A A A A Minor seventh flat five
3 3 3 3 3 Augmented
B B B B B Seventh suspended four
4 4 4 4 4 Diminished
C C C C C Diminished seventh
5 5 5 5 5 Suspended fourth
D D D D D Minor add ninth
6 6 6 6 6 Seventh
E E E E E Add ninth
7 7 7 7 7 Minor seventh
F F F F F Minor sixth
8 8 8 8 8 Major seventh
G G G G G Sixth
9 9 9 9 9 Minor major seventh
H H H H H Six ninth
2 4
7 9 A
D F
1 3 5 6 8 0 B C E G H
Chord specification
keyboard
474A-E-030A
Seite drucken