Casio Privia PX-870 Benutzerhandbuch - Seite 4
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Musikinstrument Casio Privia PX-870 herunter. Casio Privia PX-870 4 Seiten.
Seite drucken
Assembling the Stand
• Before starting assembly, check to make sure that you have all the parts shown below.
• This stand does not include any of the tools required for assembly. It is up to you to prepare a large Phillips head (+)
screwdriver for assembly.
IMPORTANT!
• Do not remove the tape securing the keyboard cover in place until assembly is complete. Removing the tape can
cause the keyboard cover to open and close during assembly, creating the risk of personal injury to your hands
and fingers.
• Do not use any screws other than those that come with the stand. Doing so risks damage to the stand and/or
Digital Piano.
• You can find the screws in a plastic bag inside the packing material.
• If screws are missing or damaged, contact your local CASIO service provider.
Part
B
A
D
(PX-870 only)
E
C
Caution!
• To assemble the stand, at least two persons should work together on a flat surface.
• Take care that you do not pinch your fingers between parts when assembling them.
• Spread felt or some other type of cloth under the bench to avoid direct contact between the rubber at the tips of the legs
and the floor surface. Direct contact between the rubber and flooring can cause discoloration, marring, or other damage to
the flooring.
• When placing the Digital Piano on the floor, be sure to place it on something soft (a blanket, cushion, etc.) Do not place the
Digital Piano directly onto the floor.
Attaching the Music Stand
Removing the Protective Tape from the
Keyboard
PX-870
1.
Protective tape is affixed to the front edges of the keyboard
Insert the tabs on the bottom of the music stand
keys to protect them during shipment. Remove the
into the two holes on the top of the piano.
protective tape before using the Digital Piano.
• Peel off the tape by pulling carefully towards you as
shown in the illustration.
PX-770
1.
Slide the music stand under the two bolts on the
top of the piano and then tighten the bolts.
• If some keys seem to be raised up after you remove the
tape, press down to return them to their normal positions.
1.
Step
IMPORTANT!
Joint connectors
• Press the joint connectors in during installation to
ensure they do not protrude from the back board
.
1.
Step
Screws
2-1.
(PX-870 only)
Step
Quantity
2-2.
Step
Screws
8 (PX-870)
2
4
2
2
6
2
● When the stand is not against a wall
2-1.
3.
Step
Step
● When the stand is against a wall
4.
Step
Pedal cable
2-2.
3.
Step
Step
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
IMPORTANT SAFETY INSTRUCTIONS
1.
Read these instructions.
2.
Keep these instructions.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this apparatus near water.
6.
Clean only with dry cloth.
7.
Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8.
Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the
point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with
the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to
avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids, such as vases, shall
be placed on the apparatus.
The power indicator being unlit does not mean the apparatus is completely disconnected from the MAINS.
When you need to have the apparatus completely disconnected from the MAINS, you must unplug the power cord. For
that purpose, locate the apparatus in a way that secures easy access to the power cord.
NOTICE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged
to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user's
authority to operate the equipment.
Declaration of Conformity
Model Number: PX-870/PX-770
Trade Name: CASIO COMPUTER CO., LTD.
Responsible party: CASIO AMERICA, INC.
Address: 570 MT. PLEASANT AVENUE, DOVER, NEW JERSEY 07801
Telephone number: 973-361-5400
This device complies with Part 15 of the FCC Rules, Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
1.
Remove the four screws (two on each end) from the
back board
, and use them to secure side panels
and
to the back board
.
• Attach the side panels so the side of the back board
where you inserted the joint connectors is facing
towards the back of the stand.
• If you have trouble inserting a screw into a joint
connector screw hole, use a screwdriver to adjust
the joint connector by rotating it.
2-1.
If you plan to locate the piano and stand where it is
not against a wall, you need to extend the anti-tip
brackets at the base of side panels
and
.
Remove the four screws (two on the inside of each
panel) that secure the brackets in place and then
slide the brackets out as shown in the illustration.
After extending the anti-tip brackets, replace the
screws you removed. Do not fully tighten the
screws yet.
2-2.
If you plan to locate the stand against a wall, loosen
the four screws at the base of side panels
and
(two on the inside of each panel) that keep the
anti-tipping brackets from sliding.
• In this case, do not remove the screws. Just loosen
them.
3.
Insert
brackets into the space between each of
the anti-tipping brackets and side panels
and
then temporarily tighten the screws you partially
tightened in step 2-1 or loosened in step 2-2.
1.
4.
Step
Screws
Place the two ends of the pedal unit
onto the
brackets and secure them with
screws. Finish
2-1.
Step
2-2.
with
screw caps.
Step
Screws
• Run the pedal cable out from the pedal unit
.
5.
While pressing the pedal unit down towards the
floor, securely tighten the screws you partially
tightened in step 3.
6.
Step
(PX-870 only)
(PX-870 only)
6.
Attach the back panel
to the back board
pedal unit
using
screws.
• Place the back panel
onto pedal unit
so it is in
front of the three screw lugs of the pedal unit.
Important!
Please note the following important information before using this product.
• Before using the AD-E24250LW/AD-A12150LW Adaptor to power the unit, be sure to check the AC Adaptor for any
damage first. Carefully check the power cord for breakage, cuts, exposed wire and other serious damage. Never let
children use an AC adaptor that is seriously damaged.
• The product is not intended for children under 3 years.
• Use only CASIO AD-E24250LW/AD-A12150LW adaptor.
• The AC adaptor is not a toy.
• Be sure to disconnect the AC adaptor before cleaning the product.
Declaration of Conformity According to EU Directive
Manufacturer:
CASIO COMPUTER CO., LTD.
6-2, Hon-machi 1-chome, Shibuya-ku, Tokyo 151-8543, Japan
Responsible within the European Union:
Casio Europe GmbH
Casio-Platz 1, 22848 Norderstedt, Germany
www.casio-europe.com
Company and product names used in this manual
may be registered trademarks of others.
This recycle mark indicates that the packaging conforms to
the environmental protection legislation in Germany.
■ About the AC adaptor that comes with the Digital Piano
Note the following important precautions to avoid damage to the AC adaptor and power cord.
• Never pull on the cord with excessive force.
• Never repeatedly pull on the cord.
• Never twist the cord at the base of the plug or connector.
• Before moving the Digital Piano, be sure to unplug the AC adaptor from the power outlet.
• Loop and bundle the power cord, but never wind it around the AC adaptor.
7.
From the back of the assembled stand, slide the
To connect the cables
piano into the grooves of side panel
and side
1.
Making sure that the pedal unit cable plug is
panel
.
oriented as shown in the illustration below, plug it
8.
Use
screws to secure the piano to the stand
into the pedal connector on the bottom of the piano.
from both the front and the back.
Bottom
9.
After confirming that all screws are securely
tightened, cover the heads with
screw caps.
Back
H
H
Pedal connector
K
a. Push the plug fully into the connector as far as it
goes.
H
b. Use clips
to secure the pedal cable to two panel
H
locations.
K
a.
K
,
H
Front
b.
H
K
L
and
Model: AD-E24250LW/AD-A12150LW
1.
Read these instructions.
2.
Keep these instructions on hand.
3.
Heed all warnings.
4.
Follow all instructions.
5.
Do not use this product near water.
6.
Clean only with a dry cloth.
7.
Do not install near radiators, heat registers, stoves, or any other source of heat (including amplifiers).
8.
Use only attachments and accessories specified by the manufacturer.
9.
Refer all servicing to qualified service personnel. Servicing is required after any of the following occurs: when the
product is damaged, when the power supply cord or plug is damaged, when liquid is spilled into the product, when
a foreign object falls into the product, when the product is exposed to rain or moisture, when the product does not
operate normally, when the product is dropped.
10. Do not allow the product to be exposed to dripping or splashing liquid. Do not place any object containing liquid on
the product.
11. Do not allow the electrical load output to exceed the label rating.
12. Make sure the surrounding area is dry before plugging into a power source.
13. Make sure the product is oriented correctly.
14. Unplug the product during lightning storms or when you do not plan to use it for a long time.
15. Do not allow product ventilation openings to become blocked. Install the product in accordance with the
manufacturer's instructions.
16. Take care the power cord is located where it will not be stepped upon or bent severely, particularly in locations
close to plugs and convenience receptacles, and in locations where it exits from the product.
17. The AC adaptor should be plugged into a power outlet as close to the product as possible to allow immediate
disconnection of the plug in case of emergency.
The symbol below is an alert indicating un-insulated hazardous voltage inside the product's enclosure, which may be
sufficient to constitute the risk of electric shock to users.
The symbol below is an alert indicating the presence of important operating and maintenance (servicing) instructions in
the documentation that accompanies the product.
• Any reproduction of the contents of this manual, either in part or its entirety, is prohibited. Except for your own, personal
use, any other use of the contents of this manual without the consent of CASIO is prohibited under copyright laws.
• IN NO EVENT SHALL CASIO BE LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT
LIMITATION, DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, LOSS OF INFORMATION)
ARISING OUT OF THE USE OF OR INABILITY TO USE THIS MANUAL OR PRODUCT, EVEN IF CASIO HAS BEEN
ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
• The contents of this manual are subject to change without notice.
USER'S GUIDE
4/4
2.
Plug the AC adaptor that comes with the Digital
Piano (PX-870: 24 VDC, PX-770: 12 VDC) into the AC
adaptor terminal. Plug the power cord of the AC
adaptor that comes with the Digital Piano into a
household power outlet as shown in the illustration
below.
AC adaptor plug
AC adaptor unit
Household power outlet
Supplied power cord
(PX-870 only)
AC Adaptor Handling Precautions
C
MA1707-B Printed in China