aevit 2.0 Installationshandbuch - Seite 16

Blättern Sie online oder laden Sie pdf Installationshandbuch für TV-Halterung aevit 2.0 herunter. aevit 2.0 17 Seiten. Mounting brackets

Seite drucken

4. SErVICE rEqUIrEMENTS

The AEVIT 2.0 Mounting Systems does not have any mandatory service requirements. however, the client should

periodically check to make sure that all adjustment knobs are tightened completely. Please contact EMC Service if you

have any questions regarding the AEVIT 2.0 Mounting Systems.

5. BEFOrE OpErATINg...

It is extremely important for your client to be fully informed about the capabilities (and limits) of these mounting

bracket systems. These mounting bracket systems were designed to provide nearly unlimited options for mounting

of the input devices. By adjusting both Adjustment Knobs, it is possible for the client to have their input device in any

position where they can operate it both effectively and comfortably. Refer to section 2.4 if you client wishes to have

the mounting system adjusted and refer to section 2.5 for other mounting options that your client may wish to utilize.

Once the client is fitted for the input devices and they are satisfied with the input device's position, time should be

taken to go over the following NOTES, CAUTIONS and WARNINGS with them.

EMC RECOMMENDS ThAT ONCE ThE CLIENT IS SATISFIED WITh ThE LOCATION AND POSITION OF ThE INPUT DEVICES,

ALL ADjUSTMENT KNOBS ShOULD BE REMOVED AND BLUE LOCTITE® ShOULD BE APPLIED TO ThE ThREADS. AFTER ThE

LOCTITE® IS APPLIED, ThE KNOBS ShOULD BE REINSTALLED AND TIGhTENED COMPLETELy. ThIS WILL PREVENT ThEM

FROM LOOSENING UNDER NORMAL OPERATION AND ACCIDENTAL IMPACTS (SEE WARNING #3).

DAMAGE MAy OCCUR TO ThE ADjUSTMENT KNOBS IF ThEy NEED TO BE REMOVED AFTER ThE BLUE LOCTITE® IS APPLIED.

MAkE SUrE ThE CLIENT IS SATISFIEd wITh ThE INpUT dEVICE pOSITION BEFOrE AppLYINg ThE BLUE LOCTITE®.

ThE ADjUSTMENT SECTION OF ThE MOUNTING SySTEMS IS DESIGNED FOR USE WITh ONE (OR MORE) 2" RUBBER WASh-

ERS (SEE FIGURES 8 & 9 PG 2-4). ThE PURPOSE OF ThIS RUBBER WAShER IS TO FULLy SECURE TWO MOUNTING BRACK-

ETS. IN ORDER TO SUFFICIENTLy SECURE ThE MOUNTING BRACKETS TOGEThER (AND COMPRESS ThE RUBBER WAShER),

IT IS IMPORTANT ThAT ALL ADjUSTMENT KNOBS BE TIGhTENED FULLY SUCh ThAT ThERE IS NO MOVEMENT UNdEr

EACh MOUNTING SySTEM WAS DESIGNED TO BREAK-AWAy UNDER LOADS ThAT ExCEED ThE NORMAL FORCES Ex-

ERTED ON ThE INPUT DEVICE. SINCE NO AEVIT 2.0 INPUT DEVICE REqUIRES A FORCE OF MORE ThAN 4 POUNDS, IF ThE

BRACKETS ARE INSTALLED CORRECTLy AND TIGhTENED PROPERLy, ThESE BRACKETS WILL REMAIN STATIONARy UNDER

hOWEVER, IF AN ExCESSIVE FORCE IS APPLIED TO ThESE BRACKETS (I.E. ACCIDENTAL IMPACTS WITh WhEEL ChAIRS,

ETC...), ThESE BRACKETS ARE DESIGNED TO BREAK AWAy. IF ThERE ARE ANy FORCED MOVEMENTS OF ThE MOUNTING

BRACKETS SUCh AS ThIS, IT IS ExTrEMELY IMpOrTANT ThAT ALL AdjUSTMENTS BE rETIghTENEd, IF pOSSIBLE.

ThE REASON FOR ThIS IS WhEN ThE BRACKETS "BREAK AWAy" AND ARE FORCED BACK INTO ThEIR ORIGINAL POSITION,

MOST ADjUSTMENT KNOBS BECOME LOOSENED IF BLUE LOCTITE® IS NOT APPLIED AND ThEREFORE WOULD NEED TO

FAILURE TO OBSERVE ThIS WARNING MAy RESULT IN ThE CLIENT OPERATING ThE VEhICLE WITh LOOSE MOUNTING

BRACKETS WhICh COULD CAUSE AN ACCIDENT RESULTING IN SERIOUS INjURy AND/OR DEATh.

IT IS ExTREMELy IMPORTANT FOR ThE CLIENT KNOW ThAT IT IS ThEIR RESPONSIBILITy TO VERIFy ThAT ALL INPUT DEVIC-

ES AND MOUNTING BRACKETS ARE SECURE BEFORE OPERATING ThE VEhICLE. ThEy ShOULD BE INFORMED ABOUT ALL

POSSIBLE ADjUSTMENTS SO ThEy CAN ChECK FOR LOOSE BRACKETS EACh TIME ThEy ENTER ThE VEhICLE.

FAILURE TO OBSERVE ThIS WARNING MAy RESULT IN ThE CLIENT OPERATING ThE VEhICLE WITh LOOSE MOUNTING

BRACKETS WhICh COULD CAUSE AN ACCIDENT RESULTING IN SERIOUS INjURy AND/OR DEATh.

NOTE #1:

cAuTION #1:

WARNING #1:

NOrMAL OpErATINg CONdITIONS.

WARNING#2:

NORMAL OPERATING CONDITIONS.

BE RETIGhTENED.

WARNING #3:

Mounting Brackets

AEVIT 2.0 MOUNTING BRACKETS INSTALL MANUAL