Audioroot eSMART BC1150 Handbuch - Seite 5
Blättern Sie online oder laden Sie pdf Handbuch für Kamera-Zubehör Audioroot eSMART BC1150 herunter. Audioroot eSMART BC1150 5 Seiten. 6 bay smart battery combiner/coupler in pc1150 with built-in 2 x 4a sequential charger and eink display
Seite druckenLi-48neo : 6.75A
Li-96neo : 11.75A
To remove batteries from the BC1150 it is recommended to lift them one by one on the side
opposing the battery's connector (right above the 5 segment LCD screen for the xxWh style batteries or
the OLED display for the xxneo style batteries).
eINK display : This screen displays the battery level for each battery as well as the combined
charge level of all batteries connected, total current draw, average termperature and estimated runtime.
As all eINK display it does not draw any current when idle. The display is automatically refreshed every 5
minutes or when a battery is inserted or removed. The display can be refreshed manually by pressing the
REFRESH button (#5). The eINK display cannot be refreshed if the DC current output switch (#7) is set to
OFF.
High priority DC input : a 10 to 15V external power supply (10A min. recommended) can be
connected to the DC IN connector (#3). Once a PSU is connected to this INPUT the BC1150 will use power
from the external supply rather than the batteries to power all equipment connected to the DC OUT
connector (#1). In the case of external power supply loss the batteries will take up seamlessly.
Built-in charger : The BC1150 has 2 x 4A smart battery chargers. To enable charging the optional
24V PSU must be connected to the XLR10F connector (#2). The charger randomly selects 2 batteries to
charge and will continuously cycle accross all 6 bays. A cooling fan will start if the charging current is
>0.5A . The air intake (#8) must be left unobstructed to allow proper cooling of the internal charging
circuitry. Additionnal air intakes are located on the internal nameplate (below the USB port) which can
allow better cooling if the lid of the pelicase is kept open during charging. Altough it is best practice to
open the BC1150's lid during charging it is abolutely not mandatory.
DC current output switch : DC output can be switched ON and OFF using this switch. It is
recommended to switch the BC1150 OFF when not in use to save battery capacity. Note : the eINK display
can only be refreshed when the switch is set to the ON position.
Legacy mode : Legacy mode should be set to ON when connecting the BC1150 to a BG-DU or K-
ART. In this mode the BC1150 emulates behaviour of a single battery on the SMBus to allow perfect
compatiblity with pre-existing products.
Soft reset : Pushing the soft reset button (#11) resets the internal microcontroller and eINK
display.
USB mini port : This port allows updating the onboard firmware using a Windows PC and USB
cable.
Overload current protection : The BC1150 is actively protected against current overloads and
short circuits. Maximum output current rating is 11.5A . In the event of a current overload or short circuit
the DC OUTPUT will switch OFF. The DC OUTPUT will be switched back ON automatically after a cool
down period of 40 seconds. It is possible to manually reset the current protection by cycling the DC
current output switch (#7) OFF and then back ON.
The BC1150 has an internal 30A fuse. This fuse cannot be replaced by the user.
WARNINGS :
Do not short circuit the output(s) of the BC1150.
•
Do not expose the BC1150 with batteries installed to temperatures avecon 120 deg. F (50 deg. C).
•
Remove batteries from the BC1150 for transport aboard passenger (PAX) or cargo (CAO) aircrafts.
•
Remove batteries from the BC1150 for long term storage (> 2 weeks). The BC1150 uses a small
•
amount of current to power the internal electronics and can fully drain batteries installed inside it
over long periods of time.
Switch the BC1150 OFF when not in use.
•
http://www.audioroot.fr [email protected]
Li-49Wh : 3.00A
Li-98Wh : 8.00A
Ce document est la propriété d'AUDIOROOT, et ne peut-être reproduit ou communiqué sans autorisation