CONTACLIP GSM-PRO Schnellstart-Handbuch - Seite 2
Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für E/A-Systeme CONTACLIP GSM-PRO herunter. CONTACLIP GSM-PRO 4 Seiten. Gsm controllable i/o module
CONTA-ELECTRONICS
=====GSM controllable I
=====
=====
=====
GSM controllable I/ / / / O module
O module
GSM controllable I
GSM controllable I
O module
O module
Note
Note
Note
Note
=
This document is a quick start guide. For further details the complete manual can be
downloaded at:
http://www.conta-clip.com/en/service/
=
Placing the SIM card
Placing the
SIM card
Placing the
Placing the
SIM card
SIM card
KEEP ESD PRECAUTIONS IN MIND WHEN OPENING THE MODULE!
To open the module lift the lid with a small flat screwdriver.
Place a SIM card into the SIM card holder inside the module. When a SIM card with PIN code is
inserted the PIN code must be entered in the configuration interface.
Replace the lid and connect the antenna.
Connect the module to the 24VDC power supply. After 10 seconds the first LED's activate.
After 90 seconds the 'RUN' LED should stop blinking the module is now ready for use.
Configure and connecting the module
Configure and connecting the module
Configure and connecting the module
Configure and connecting the module
Download and install the configuration interface:
http://www.conta-clip.com/en/service/
Connect the module with a USB cable to the PC.
Start the configuration program and it will connect to the module. The module is now ready
for configuration.
The wiring configuration for I/O and power is shown at the top of the module.
Led status
Led status
Led status
Led status
The Led 'Run' indicates module activity:
The Led 'Com' indicates network activity: green ON = connected to GSM network
The Led 'Busy' indicates modem activity: ON
=====
=
=
Flash
= starting up
ON
= ready for use
green Flash = roaming GSM network
green OFF = not connected to GSM network
red ON
= error
= module currently busy
Further information:
=
=
=
Default message structure
Default message structure
Default message structure
Default message structure
n = channel number
x = digital: 0= off, 1= on, 2= don't change, 3= toggle
Get status of ALL IOs:
Get status of ALL IOs:
Get status of ALL IOs:
Get status of ALL IOs:
(Digital Outputs)
Write multiple DOs:
Write multiple DOs:
Write multiple DOs:
Write multiple DOs:
Write single DO:
Write single DO:
Write single DO:
Write single DO:
Read multiple DOs:
Read multiple DOs:
Read multiple DOs:
Read multiple DOs:
Read single DO:
Read single DO:
Read single DO:
Read single DO:
(Universal Inputs)
Read multiple UIs:
Read multiple UIs:
Read multiple UIs:
Read multiple UIs:
Read single UI:
Read single UI:
Read single UI:
Read single UI:
Module Reset:
Module Reset:
Module Reset:
Module Reset:
NOTE:
DOn /UIn can be replaced by a user given name with the configuration interface.
NOTE:
Correct sending and receiving of data depends on the network quality of your provider.=
www.conta-clip.com
Cat. No.: 95121.5
=
=
=
SMS:
RALL
RALL
RALL
RALL
Answer: 'read: DO1=x, DO2=x, DO3=x, DO4=x'
'UI1=xxx, UI2=xxx, ....... UI8=xxx'
SMS:
WMDO
WMDOxxxx
WMDO
WMDO
Answer: 'status DO1=x, DO2=x, DO3=x, DO4=x'
SMS:
WDOnx
WDO
WDO
WDO
Answer: 'status DOn=x'
SMS:
RMDO
RMDO
RMDO
RMDO
Answer: 'read DO1=x, DO2=x, DO3=x, DO4=x'
SMS:
RDOn
RDO
RDO
RDO
Answer: 'read DOn=x'
SMS:
RMUI
RMUI
RMUI
RMUI
Answer (digital): 'read UI1=x, UI2=x, .... UI8=x'
(analog): 'read UI1=xxxx, UI2=xxxx, .... UI8=xxxx'
SMS:
RUIn
RUI
RUI
RUI
Answer (digital): 'read UIn=x'
(analog): 'read UIn=xxxx'
SMS:
WRESET
WRESET
WRESET
WRESET
Answer: Powercycle message
Further information:
=
GSM- - - - PRO
GSM
GSM
GSM
PRO=
PRO
PRO
www.conta-clip.com