Contacta Limited SecuriCom System Manual - Seite 10

Blättern Sie online oder laden Sie pdf System Manual für Telefon Contacta Limited SecuriCom herunter. Contacta Limited SecuriCom 19 Seiten. Speech transfer system

Seite drucken
SECURICOM SPEECH TRANSFER SYSTEM
Siting and Installing the Staff Unit
Amplifier Connections
Connecting Components
to the Amplifier
The STS-F70 Staff Unit is a self standing module for the Staff Side. It should be placed conveniently on
the counter top so the cashier can hear the loudspeaker and talk into the gooseneck microphone to
the customer. The microphone is of the close talking type so background noise is not picked up. A
'Mute' switch is located on the front of the Staff Unit. In the absence of a cable port, a suitably sized
hole should be drilled into the counter top at the rear of the Staff Unit to take the reinforced cable.
Disconnect the 2 two-way plugs before introducing the cables for a neater installation. Ensure these
are re-connected correctly or the system will not operate.
1
LED/Tone (+)
2
LED/Tone (-)
3
Staff Unit Mic 1 (+)
4
Staff Unit Mic 1 (screen)
5
Customer Mic 1 (+)
6
Customer Mic 1 (screen)
7
Staff Mic 2 (+)
Contacta Communication Systems Limited
Tel: 0181 858 2123
Induction
20 19
-
Connection
to Induction
Loop Aerial
Each component (Microphone, Loudspeaker, Staff Unit or Induction Loop) comes fitted with two-way
connection plug(s) which locate into the appropriate socket(s) at the rear of the Amplifier. The plugs
connect to the cables by screw terminal connections so cables can be removed and fed through small,
neat apertures for an unobtrusive, discrete installation. However, the cables and plugs must be re-con-
nected correctly or the system will not operate. If in
doubt, mark the wires before disconnecting the plug(s). If
there is a suitable cable port on the cashiers side, the
Staff Unit cables can be diverted through this without the
need to remove and re-connect the 2 two-way plugs.
Controls are provided on the front of the Amplifier. The
Controls
latching push switch marked 'power' switches the unit
on or off, a red LED indicates when the unit is on. Two
rotary volume controls marked 'customer' and 'staff'
adjust output from the loudspeakers. The volume of the
system may be adjusted by turning the rotary volume
controls clockwise (to increase the level of sound) or
anticlockwise (to decrease the level of sound).
8
Staff Mic 2 (screen)
9
Customer Mic 2 (+)
10 Customer Mic 2 (screen)
11 Staff Unit Speaker (+)
12 Staff Unit Speaker (-)
13 Customer Speaker 1 (+)
14 Customer Speaker 1 (-)
Rear of Amplifier showing two-way connections for components
Cust
Staff
Cust
Staff
Loop
Spk 2 Spk 2
Spk 1 Spk 1
- +
-
+ -
+
-
+
-
+
18 17 16 15
14 13 12
11
+
+
+
-
+
-
-
+
-
Optional
Connect
Connect
connections to
to
to Staff
second
customer
Unit
loudspeakers
loud
speaker
15 Staff Speaker 2 (+)
16 Staff Speaker 2 (-)
17 Customer Speaker 2 (+)
18 Customer Speaker 2 (-)
19 Induction Loop Aerial (+)
20 Induction Loop Aerial (-)
Power in
Cust
Staff
Cust
Staff
Mic 2 Mic 2
Mic 1 Mic 1
LED Tone
Sc + Sc +
Sc + Sc +
-
10 9
8 7
6
5
4
3
2
+
+
+
+
-
Sc
Sc
Sc
Sc
Optional
Connect
Connect
Connection
connections
to
to Staff
to LED or
to second
customer
Unit
tone signal
microphones
micro-
(optional)
phone
Negative -
or
Screened
Cable
Positive +
Enlarged drawing of two-way plug that connects
components to the rear of the amplifier
INSTALLATION
+
1
Connection
plugs
+
11