Addonics Technologies AD2M2SAR Benutzerhandbuch - Seite 2

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Adapter Addonics Technologies AD2M2SAR herunter. Addonics Technologies AD2M2SAR 2 Seiten. Dual m2 ssd adapter

Seite drucken

Overview

Drive 2

Connector

RAID Mode

SATA

Jumper Block

Connectors

ERROR LED: glows red temporarily when power is first connected. Will glow red steadily to indicate an I/O

error occurred on the mSATA drive.

a M2 SSD

Activity LED: glows green to indicate an mSATA device in inserted and powered up, blinks to indicate

activity. Both Drive Activity LEDs will blink rapidly during a RAID 1 rebuild function.

SATA

HOST LED: glows green to indicate connection to SATA controller, blinks to indicate activity.

Drive Installation

M2 SSD

Insert one or two mSATA media devices into the Drive connectors, at an angle, then press downward gently

location that matches the length of the M2. Secure the M2 to the mounting pole with the screw provided.

until the drive snaps in place under the retaining clip.

Port Multiplier Compatibility

The Port Multiplier built into this device will only work with a Port Multiplier aware SATA host adapter when

configured as JBOD (individual drives). Identify your host controller and check with its hardware

manufacturer if you are unsure. Addonics offers several Port Multiplier aware host adapters. This

requirement does not apply to RAID Modes.

Hot Swapping

This device supports hot swapping (inserting or removing drives while the drives are running and connected

to a computer). The eSATA controller on the computer must also support hot swapping - be sure to confirm

this before attempting to insert or remove drives while the system is running. Also be sure to practice the

appropriate safe removal procedure before proceeding. Failure to practice safe removal procedures will

result in loss or corruption of data.

www.addonics.com

Drive 2 Activity

and Error LEDs

Drive 1 Activity

and Error LEDs

HOST LED

SET Jumper

Retaining Clip

Drive 1

Connector

Move the mounting pole to the

Technical Support (M-F 8:30 am – 6:00 pm)

Setting Up the Adapter

M2 SSD

The Dual mSATA – SATA Adapter is factory set for JBOD Mode. Each drive will be treated as an individual

target by the SATA controller, which is required to support Port Multipliers. RAID 0, RAID 1, and LARGE

Modes do not require port multiplier support.

The RAID Mode Jumper Block determines the mode when the adapter is powered up while the SET

Jumper's shunt is connected between SET and GND. To set the RAID Mode, arrange the two shunts on the

RAID Mode Jumper Block according to the table below, make sure the SET Jumper's shunt is connecting

SET and GND, then power up the adapter one time with a connection to a SATA controller. Once the

operating system shows the storage, the RAID Mode is configured.

After the RAID Mode has been set up correctly, the SET Jumper may be disabled by moving the shunt to

connect between SET and NC to prevent unintended configuration later.

NOTE: An existing RAID can only be changed to JBOD Mode. To change the type of RAID, you must first

delete the RAID by powering up the adapter with the jumpers set to JBOD Mode one time, then disconnect

power and set the desired RAID Mode afterward.

The RAID Mode Jumper Block's pins are numbered as

shown here, with the board oriented component side up.

MODE

JUMPER 1, 2, 3

JBOD (PM)

RAID 0 (R0)

RAID 1 (R1)

LARGE (SP)

Phone: 408-453-6212

JUMPER 4, 5, 6

2-3

5-6

1-2

4-5

2-3

4-5

1-2

5-6

Email: