Apollo 55000-450 Einbauanleitung

Blättern Sie online oder laden Sie pdf Einbauanleitung für Sicherheitssensoren Apollo 55000-450 herunter. Apollo 55000-450 2 Seiten. Xp95a and discovery smoke & heat detectors

Seite drucken

Technical Data XP95A

Detector Model No.

55000-450

55000-550/555*

Detector Type

Heat

Ionization

Working Voltage

17-28V dc

Modulation Voltage

5-9V

(V peak to peak)

Maximum Alarm

2.5mA

Current LED on

Surge Current

1.0mA

Supervisory Current

250μA

280μA

Heat Element Rating

131ºF (55ºC)

N/A

Compatibility Identiﬁ er

55000-450

55000-550/555*

Test Method

•Hair dryer

•Home safeguard

•Gemini 501

Control Panel

Refer to: www.apollo-ﬁ re.co.uk for compatible panels.

*Please note 55000-555 is ULC listed only.

Technical Data Discovery

Detector Model No.

58000-450

58000-550

Detector Type

Heat

Ionization

Working Voltage

17-28V dc

Modulation Voltage

5-9V dc

(V peak to peak)

Maximum Alarm

3.5mA

Current LED on

Surge Current

1.0mA

Supervisory Current

500μA

400μA

Heat Element Rating

135ºF (57ºC)

N/A

-210ºF (99ºC)

Compatibility Identiﬁ er

58000-450

58000-550

Test Method

•Hair dryer

•Home safeguard

•Sensitivity test

•No Climb

•Gemini 501

Control Panel

Refer to: www.apollo-ﬁ re.co-uk for compatible panels.

©Apollo Fire Detectors Ltd 2017

Apollo Fire Detectors Ltd, 36 Brookside Road, Havant, Hants, PO9 1JR, UK

Tel +44 (0)23 9249 2412 Fax +44 (0)23 9249 2754

Email: techsales@apollo-ﬁ re.com Website: www.apollo-ﬁ re.co.uk

In the USA: Apollo America Inc., 25 Corporate Drive, Auburn Hills, Michigan, 48326, USA

Tel: (248) 332-3900 Fax: (248) 692-0888

Email: info.us@apollo-ﬁ re.com Website: www.apollo-ﬁ re.com

39214-035/Issue 11

55000-650

55000-886

Photoelectric

Multisensor

17-28V dc

5-9V

4.5mA

3.5mA

1.0mA

340μA

500μA

N/A

55000-650

55000-886

•Home safeguard

•Gemini 501

58000-650

58000-750

Photoelectric

Multisensor

17-28V dc

5-9V dc

3.5mA

1.0mA

500μA

N/A

135ºF (57ºC)

(Mode 5)

58000-650

58000-750

•Home safeguard

•Sensitivity test

•No Climb

•Gemini 501

•Hair dryer (heat

sensor only)

XP95A and Discovery Smoke & Heat Detectors

Installation Instructions

General

These instructions apply to Apollo detector base 45681-210, to variants of this base and to

the associated ranges of UL listed XP95A and Discovery detectors which are listed overleaf.

Installation

These products must be installed in accordance with the applicable NFPA standards, local

codes and jurisdictional authorities. Failure to follow these instructions may result in failure

of the detectors to report an alarm condition. Apollo Fire Detectors Limited is not responsi-

ble for detectors which are improperly installed, maintained and tested.

The FM approval for these initiating devices does not include or imply approval of the

control unit to which it may be connected. In order to maintain an FM approved system,

these initiating devices must be listed with an FM approved compatible control panel. For

more information on RTI classiﬁ cation refer to FM class standard 3210.

Before installing these products check the continuity, polarity and insulation resistance of all

wiring. Check that installation is in accordance with the ﬁ re system drawings and conforms

to all applicable local codes such as NFPA 72.

Use 3" octagonal box for direct connection to the base. 4" octagonal and 4" square boxes

may be used with proper UL listed mounting brackets. When mounting on a wall, install 4" to

12" from the ceiling. Use 3M Weatherban 606 Non-Flammable sealing compound (or equiv-

alent) to seal ﬁ eld wiring conduit opening in the electrical box, this will reduce the stack

effect. Secure the base to the electrical box with appropriate screws. Do not overtighten

the screws. The raised mark on the side of the base indicates the direction of the detec-

tor LED when ﬁ tted. Connect the shield, if required, to the SHIELD terminal on the base. For

information on how to set the address of each device correctly refer to the section 'Address

Setting' overleaf.