Duren 321240 Gebrauchsanweisung - Seite 5
Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Farbspritzgerät Duren 321240 herunter. Duren 321240 13 Seiten. Electric hvlp turbine spray gun system
Seite druckenPLEASE KEEP THIS MANUAL IN A SAFE PLACE FOR FUTURE REFERENCE
40
Be aware of the dangers of working in or on and building or material containing asbestos.
Always take a appropriate measures up to an including contracting licensed 3rd parties
to remove and/or make safe and articles or asbestos.
41
If the material sprayed makes contact with eyes, skin or enters the respiratory system
take appropriate measures as advised by the HSE and your own Health and Safety
guidelines. If in doubt, seek medical help.
42
NEVER point air supply hose at yourself or others.
43
Be aware of the dangers and hazards of spraying isocyanate based paints.
44
Accidents involving power tools can be caused by over familiarity. Implement and encourage a
disciplined work ethic at all times
45
NEVER use the polisher whilst the floor underfoot is wet or slippery.
46
NEVER use the polisher when standing on an unstable surface.
47
Always maintain the tool in top condition to keep it working safely and efficiently. Follow instructions
and use a specialist 3rd party company if required.
48
DO NOT smoke whilst using this tool and to not allow bystanders to smoke nearby - smoking in a
public place is not permitted under law.
Switch off unit immediately if;
1
There is interruption of mains electrical supply such as in the case of a power cut.
2
There damage occurs to the socket, plug, cable or cable entry into the unit.
3
There is damage to the on/off switch on the unit.
4
There is a smell of burning plastic.
5
There is smoke coming from the motor housing.
If in any doubt as to your own safety, cut the power at the main fuse board. Always familiarise yourself with the
electrical layout of your work area.
Operating Instructions
Preparation
To obtain the best results, it is important that you prepare the surface to be sprayed and thin the paint to the cor-
rect viscosity before you start work. Always ensure that the surface to be sprayed is free from dust, dirt, grease
and other foreign bodies. Always mask the areas around the areas to be sprayed using good quality masking
tape. The paint to be sprayed should be suited to the task and compatible with your spraygun. There should be
no lumps or other particles. Make sure that you have a properly working strainer. Many substances can be
sprayed with this gun but it is important that you check with your paint supplier before purchasing your paint. It is
very important that you check the panel for signs of silicone contamination before starting work.
Thinning
Most paints are supplied ready for the type of application and applying technique but may have to be thinned for
use with your spraygun. Always follow the paint manufactures advice on thinning paint. The viscosity cup sup-
plied will help you determine the correct viscosity of the paint to be used. To measure the viscosity if the paint fill
the cup to the brim and measure the length of time it take to empty. The table below shows the recommended
times for different materials. Please note that this is intended as a guide only and you should advice from your
paint supplier.
Plastic & Latex
Primers
Oil based paints
Aluminium paints
Wood sealers
Wood stains
If the paint takes longer than the recommended time to empty, further thinning is required. Mix a small quantity of
the appropriate thinner and use the viscosity cup again until the required figure is achieved. Some paints contain
lumps and particles and these should be strained before use.
Spraying
Fill the paint cup with the appropriately thinned paint and screw onto the gun. Connect the air hose and then plug
in the mains supply and switch on. It is recommended that you use a test card or scrap panel to make sure that
24-28secs
24-28secs
18-22secs
22-25secs
28-35secs
Not required
Duren Tools
T: 01582 484875 E: [email protected]
www.duren.co.uk
Water based Paint
Varnishes
Enamel paints
Car underseal
Wood preservatives
20-25secs
20-25secs
18-22secs
25-35secs
Not required