AddSecure IRIS-4 160 Handbuch für Schnellinstallation und Wartung - Seite 5

Blättern Sie online oder laden Sie pdf Handbuch für Schnellinstallation und Wartung für Touch-Terminals AddSecure IRIS-4 160 herunter. AddSecure IRIS-4 160 11 Seiten.

Seite drucken

IRIS-4 160

Quick Installation and

Maintenance Guide

6.5. 4g/3g/2g SIM Card

DO NOT FIT SIM card until after you have

performed the 4G/3G/2G Network Scan detailed in

the Section 6 . 9 "Configuration" . You will be prompt-

ed when to insert the SIM card .

6.6. Dial Capture

Dial Capture enabled systems: Connect the two dial

screw terminals to the alarm panel dialler telecoms

line connection . If the alarm panel has screw connec-

tions .

Note: Polarity is not important in this instance.

For EN 50136-2: 2013 compliance fit the supplied

18K sense resistor in parallel with the dialler output

of the alarm panel, at the alarm panel end of the

cable.

Note: This resistor enables the dialler to detect

cable faults and/or tampers, the Monitoring Centre

will also need to enable the dial port monitoring

on the IRIS Secure Apps software to receive alarm

notifications.

6.7. Pin Inputs

The IRIS-4 160 dialler has four pin inputs that can be

used to generate messages, These can be:

• Text messages via SMS (4G/3G/2G).

• SIA, Contact ID or Fast Format alarm messages

over IP to the monitoring centre .

Note: You can also use the Pin alarm inputs in

addition when directly connected to an alarm panel

via the dial capture, serial or RS485 connections.

Via Open/Close Contact Source

Each pin input is designed to be connected in a loop

via an open/close contact source from an alarm pan-

el, or other device, to a reference ground pin available

on the IRIS-4 160 dialler, as shown below .

Opening the contact (i . e . loop is open circuit)

generates an alarm signal . Closing the contact gener-

ates the equivalent restore signal .

Via Sense Resistors

It is also possible to link the contacts to the IRIS-4

160 dialler via sense resistors so that an open or short

circuit tamper on the loop is detectable and the

Monitoring Centre alerted . In this case, the connec-

tions made should be as shown below .

Note: For this feature to work correctly it is

essential to connect the resistor at the contact end

of the loop and not the dialler end. The Monitoring

Centre must also enable the monitoring of this

facility on the dialler within the IRIS Secure Apps

receiving system.

6.8. Switch on

To confirm power is applied, look for the indicator

'SYS LED' flashing red on the IRIS-4 160 dialler

board, top left hand corner .

6.9. Configuration

To configure the dialler, use any of the following the

methods:

• Web browser via Wi-Fi.

• AddSecure IRIS Bluetooth App.

• Alarm panel integration e.g. Honeywell Galaxy

(RS485 connection) Texecom Premier range

(RS232 TTL connection) .

Note: Please configure the alarm panel first for

connections to Honeywell Galaxy or Texecom

Premier on the serial integration, as these will

transmit configuration to the IRIS-4 160 dialler.

For more details on the alarm panel integration,

download the full panel installation manual from

http://www.addsecure.com.

• Connect the board's Micro USB connector to

a laptop/PC running the IRIS Toolbox soft-

ware . Download the IRIS Toolbox user guide

from http://www . a ddsecure . c om .

IRIS-4 160

Defaulting

If at any point a complete default of the dialler is

required, use the following procedure:

1 . Completely power down the IRIS-4 160 by

removing the power and one of the batteries

(if fitted) .

2 . Now press and hold down the AP button .

3 . Reconnect the batteries if needed and reapply

power whilst still holding down the AP button

for 10 seconds .