Cayken SCY-520WEQ Benutzerhandbuch - Seite 7

Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Kutter Cayken SCY-520WEQ herunter. Cayken SCY-520WEQ 9 Seiten. Wall cutter

Seite drucken

guide rail outfit.The number of the setscrew depends on the

softness of the cutting plane.The track way must be fixed

tightly.

4.Fix the host machine according to the progressing mark on

it.Fix the speed control,the plug and the handwheel rotating in

counter-clockwise and then the host machine can run on the track

way.

5.Fix the saw web.The diameter of the internal hole of the host

machine is 355mm.The hexagonal screw to fix the saw web must be

fastened by the open and wrench.

6.The saw web aims at the cutting plane line.Fix the track way

totally,adjust flatly the six hexagon heads on the track way with

the hexagon spanner and move up and down the screws to be on the

same horizontal line. Thus the track way can not break away from

the joint.

7.Aim at the plug connecting the cable.

B.Cutting instructions

8.Insert the water pipe into the inlet valve to supply

water.Regulate the water and make it abundantly on the cutting

plane.

9.Turn on the switch on the control cabinet and the switch on the

control cabinet and the switch of the host machine.

10.After

rotating

the

cutter

slowly.The saw web move downwards to touch the cut parts.The saw

web must move slowly.When the cuts to the preset depth,rotate

the handwheel to cut.

(then you should turn on the machine's switches for moving up

and

down

forward,adjust

cutting.)You can adjust the cutting speed when it cuts into the

wall.The cutter must keep a low and uniform velocity when coming

into reinforcing steel bars.If it cuts too deep at the

beginning,it is excessive work for the machine,which will

decrease the cutting speed.

11.Dissemble the host machine from the track way and clean up the

working area after the cutting.

Notes when the cutter is working:

a.If the cut part is hard and thick,the best way is to cut it

twice.That is, if the cut part is 20cm thick,cut into 10cm first

and then cut into 10cm again.In this way,it will raise the

cutting efficiency,and reduce the spoilage to the saw web.

handwheel,in

start

cutting

the

speed

and

make

electric

b.Do not plug in when fixing or dissembling the saw web in

case of accident.

c.The machine can not work over 10hours every day.It is

better to cool it for a while after it keeps working for

two or three hours and then it can work again.

Chapter8. Fittings

The track way has two sizes of 1.2m and 1.8m.The user can

order other size of track way accordingly.

Chapter9. Maintenance and Inspection

Note:Do not plug in before checking the machine.

The accumulative working hours of the machine can not exceed

24hours.

Then it must be thoroughly cleaned up and maintained.You should

especially guarantee the lubrication and flexibility of the

lifting screw and the lifting screw and the lifter of the host

machine.(They can not have any slurry and sundries,which is good

for operation.On the contrary,it will damage the machine.)

1.Check the saw web

Using attrited saw web will reduce the cutting efficiency and

make the motor overwork.The saw web needs to be changed timely.

2.Check the chain wheel

Check whether the 16chain wheels under the foundation are stuck

or fail to work.The space between the chain wheel and the track

way is no more than 0.2mm,or else you should loosen the screw

caps for fastening the chain wheels and adjust the hexagonal

tightening screws at both sides of the foundation accordingly.

3.Check the chain wheel

Check monthly the depth of parallelism between the moving

direction of the saw web and the track way.If the distance

between the saw web and the track way can not be more than 1mm,or

else the saw web maybe stuck