BENDIX AR-2 ANTILOCK RELAY VALVE Handbuch - Seite 10
Blättern Sie online oder laden Sie pdf Handbuch für Kontrolleinheit BENDIX AR-2 ANTILOCK RELAY VALVE herunter. BENDIX AR-2 ANTILOCK RELAY VALVE 12 Seiten. Antilock relay valve
Seite drucken
DISASSEMBLY
GENERAL
The following disassembly and assembly procedure is
presented for reference purposes only and presupposes
that the appropriate maintenance kit is on hand at the time
of disassembly. The instructions provided with the
maintenance kit should always be used in lieu of those
presented here. Refer to figure 10 throughout the disassembly
and assembly procedure. CAUTION: The AR-2
be lightly clamped in a bench vise during disassembly,
however, over clamping will cause damage to the valve and
result in leakage and/or malfunction. If a vise is to be used,
position the valve so that the jaws bear on the supply ports
on opposing sides of the valve's body.
1. Remove all air fittings and plugs from the AR-2
2. Mark the relationship of the antilock electronic controller
(2) and valve cover (4) to the body (9). Note the position
of the mounting bracket (6) and mark the relationship of
the bracket to the valve body (9), cover (4), and antilock
controller (2). Remove and retain the four cap screws
and lock washers (1) that secure the controller to the
cover (4), then carefully remove the electronic controller
without damaging its gasket (3).
3. While holding the exhaust cover (11), remove the retaining
ring (10) that secures it to the body (9).
4. Remove the exhaust cover (11) along with both o-rings
(12 & 13).
5. Remove the valve spring (14), valve retainer (15), and
the valve assembly (16) from the body (9).
6. Remove and retain the two cap screws and lock washers
(5) that secure the bracket (6) to the cover (4). Remove
and retain the two bolts with lock washers (7), and nuts
(8) that secure the cover (4) and mounting bracket to
the valve body (9). Then remove the remaining two cap
screws (7) that secure the cover (4) to the body (9).
7. Separate the cover (4) and mounting bracket (6) from
the body (9), then remove the large and small sealing
rings (19 & 40).
8. Remove and retain the relay piston (17) and relay piston
spring (if present) from the body (9). NOTE: The relay
piston spring is not used in all AR-2
9. Remove the o-ring (18) from the relay piston (17).
10. Remove the retaining ring (20) from the cover (4), then
remove the exhaust piston (21).
11. Remove the exhaust piston o-ring (22).
12. Remove the service piston (23) from the cover (4).
13. Remove the spring (24) and spring cage (25) from the
cover (4).
14. Remove the blend back piston (26) from the valve cover
(4), then remove both o-rings (27 & 28).
10
15. Remove the proportioning piston (30) from the valve cover
16. While holding the inlet valve seat (34) in place, remove
17. Remove the inlet valve seat (34), the inlet valve (33),
18. Remove the exhaust diaphragm screw (37), washer (38)
™
valve may
CLEANING & INSPECTION
1. Using mineral spirits or an equivalent solvent, clean and
2. Inspect the interior and exterior of all metal parts that
™
valve.
3. Inspect the bores of both the body (9) and cover (4) for
4. Make certain all air channels and exhaust passages in
5. Inspect the pipe threads in the body (9). Make certain
6. Wash all non-metallic components in a soap and water
7. If the valve was equipped with a relay piston spring,
8. Inspect all air line fittings for corrosion and replace as
ASSEMBLY
1. Prior to assembly, lubricate all o-rings, seals, and pistons,
™
valves.
2. Install the o-ring (35) on the inlet valve seat (34).
3. Insert the inlet and exhaust valve spring (32), LARGE
4. Install the inlet and exhaust valve (33) inside the inlet
(4), then remove both o-rings (29 & 31).
the retaining ring (36) from the proportioning piston (30).
and the valve spring (32) from the proportioning piston
(30), then remove the o-ring (35) from the valve seat (34).
and exhaust diaphragm (39) from the cover (4).
thoroughly dry all metal parts.
will be reused for severe corrosion, pitting and cracks.
Superficial corrosion and/or pitting on the exterior
portion of the body (9) and cover (4) is acceptable.
Replace the entire valve if the interior of the body or
cover exhibit signs of corrosion or pitting.
deep scuffing or gouges. Replace the entire valve if
either are found.
the valve cover (4) are clear and free of obstruction.
they are clean and free of thread sealant.
solution making certain to rinse and dry thoroughly.
Inspect each non-metallic component for cracks, wear
or distortion. Replace the entire valve if these conditions
are found.
inspect it for signs of corrosion, pitting and cracks.
Replace as necessary.
necessary. Make certain to remove all old thread sealant
before reuse.
as well as body and cover bores, using the lubricant
provided with the Bendix maintenance kit.
END FIRST, into the proportioning piston (30).
valve seat (34) making certain that the four tabs are
within the bore of the seat.