BENDIX TP-4 TRACTOR PROTECTION VALVE Handbuch - Seite 5
Blättern Sie online oder laden Sie pdf Handbuch für Kontrolleinheit BENDIX TP-4 TRACTOR PROTECTION VALVE herunter. BENDIX TP-4 TRACTOR PROTECTION VALVE 6 Seiten. Tractor protection valve
Seite drucken
NOTE: When using pipe thread sealant during assembly
and installation, take particular care to prevent the
sealant from entering the valve itself. Apply the
sealant beginning with the second thread back
from the end.
1. Install inlet valve (6). Install o-ring (5) on valve retainer
(14). Install spring (7) and valve retainer. Install retainer
ring (13) making certain it is engaged in groove.
2. Install double check valve guides in intermediate body
and install shuttles (4) in guides.
3. Install spring (8) in body. Install o-rings (2) and (3)
on piston (12). Insert stem of piston inside of spring,
making sure vent is open.
4. Install new gaskets (9) and (10) on both sides
of intermediate body (Note: locating pins match
corresponding holes in gasket). Install lower and upper
bodies with assembly in the following manner.
A. Torque center two (2) cap screws to 80" lbs.
B. Torque upper right and lower left cap screws to
80" lbs.
C. Torque lower right and upper left cap screws to
80" lbs.
D. IMPORTANT - Repeat steps A, B, and C.
TESTING REBUILT TP-4
Perform Operating and Leakage Tests, as outlined in
"Service Checks" section.
WARNING! PLEASE READ AND FOLLOW
THESE INSTRUCTIONS TO AVOID PERSONAL
INJURY OR DEATH:
When working on or around a vehicle, the following
general precautions should be observed at all times.
1. Park the vehicle on a level surface, apply the
parking brakes, and always block the wheels.
Always wear safety glasses.
2. Stop the engine and remove ignition key when
working under or around the vehicle. When
working in the engine compartment, the engine
should be shut off and the ignition key should be
removed. Where circumstances require that the
™
VALVE
engine be in operation, EXTREME CAUTION should
be used to prevent personal injury resulting from
contact with moving, rotating, leaking, heated or
electrically charged components.
3. Do not attempt to install, remove, disassemble
or assemble a component until you have read
and thoroughly understand the recommended
procedures. Use only the proper tools and observe
all precautions pertaining to use of those tools.
4. If the work is being performed on the vehicle's
air brake system, or any auxiliary pressurized air
systems, make certain to drain the air pressure
from all reservoirs before beginning ANY work
on the vehicle. If the vehicle is equipped with an
®
AD-IS
air dryer system or a dryer reservoir module,
be sure to drain the purge reservoir.
5. Following the vehicle manufacturer's recommended
procedures, deactivate the electrical system in a
manner that safely removes all electrical power
from the vehicle.
6. Never exceed manufacturer's recommended
pressures.
7. Never connect or disconnect a hose or line
containing pressure; it may whip. Never remove
a component or plug unless you are certain all
system pressure has been depleted.
8. Use only genuine Bendix
components and kits. Replacement hardware,
tubing, hose, fi ttings, etc. must be of equivalent
size, type and strength as original equipment and
be designed specifi cally for such applications and
systems.
9. Components with stripped threads or damaged
parts should be replaced rather than repaired. Do
not attempt repairs requiring machining or welding
unless specifi cally stated and approved by the
vehicle and component manufacturer.
10. Prior to returning the vehicle to service, make
certain all components and systems are restored
to their proper operating condition.
11. For vehicles with Antilock Traction Control (ATC),
the ATC function must be disabled (ATC indicator
lamp should be ON) prior to performing any vehicle
maintenance where one or more wheels on a drive
axle are lifted off the ground and moving.
®
replacement parts,
5