Great Canadian Systems IQ-LD Betriebshandbuch - Seite 5

Blättern Sie online oder laden Sie pdf Betriebshandbuch für Kaffeemaschine Great Canadian Systems IQ-LD herunter. Great Canadian Systems IQ-LD 12 Seiten. Newco iq2000p: operation manual

Seite drucken

initiated by depressing the hidden brew button labeled in fig 1, page 2 as HALF BREW. If this feature is desired

use the Select button to choose "Yes". Select "No" to disable Brew #2.

Brew Time #2

1:45

Buzzer Delay

0:40

the second portion of the brew cycle. The minimum buzzer delay time is 10 seconds and the maximum is 2

minutes. If a buzzer is not desired it may be turned off by selecting "None" under Buzzer Type below. Note that

Brew #1 and Brew #2 both use the same buzzer delay time so the longer delay time should be used.

Auto Arm Enable

Yes

preventing the decanter from being removed prematurely. When the tank reaches the preset temperature level the

brew cycle will begin and the display will indicate "Coffee Brewing".

Brew Time Remaining

Yes

Temperature Setpoint

display window to decrease or increase the tank temperature as desired. The temperature at the low end of the

range is approximately 170 degrees and at the upper end is approximately 212 degrees.

Power Save Enable

Yes

the switch on the column to the OFF position when power save was to be activated. Power save is based on the

brewing activity. When the brewer has not been used for a period of 2 hours the unit will go into Power Save

mode. When this feature is not enabled the tank temperature will be maintained at the brew set point temperature.

(The switch on the column now turns off power to the brewer disabling all brewer functions.)

Buzzer Type

Burst

buzzer function.

Keypad Beep Enable

Yes

function.

Service Cycles

00800

even though this message is displayed. Note that the name and telephone number which will be displayed may be

programmed as outlined in the Custom Message Programing Section under message number "SRV".

Exit Pgm/Srv Mode

Yes

Program and go back through the program items listed above or you may select Service and review or set those

items. Use the select button to choose Yes or No and then depress Enter. If the brewer detects that there has

been no activity on the keypad for 1 minute it will exit to the ready/standby mode by itself.

If you answered yes to the previous option you will be asked to set the brew time

for this function. Follow the steps previously outlined for Brew Time #1 above. The

minimum and maximum program times are the same as noted for Brew #1.

This function is to set the delay for the buzzer which indicates that the coffee is

finished brewing. This delay is intended to account for the time from which the

dump valve shuts off until the coffee finishes dripping from the brew basket. This is

The auto arm function will not allow the brew cycle to start until the water

temperature is at the preset temperature level. If the brew button is pressed while

the tank is heating the display will indicate "Brew Cycle Activated" to aid in

Answering yes enables the brew time remaining to be displayed during the brew

cycle. The Brew Time and the Buzzer Delay are added together for the total brew

time. Coffee Brewing and Time Remaining will display throughout the brew cycle.

This is the method for controlling the water temperature in the tank. It is similar to

the function of a thermostat knob. Use the "-" or "+" keys to move the * (asterisk)

back and forth between the "-" (decrease) and the "+" (increase) symbols in the

When power save is enabled the brewer will allow the tank temperature to drop to

the standby temperature of approximately 170 degrees after a period of inactivity in

order to reduce power consumption. On previous models it was necessary to turn

There are 5 possible selections for the buzzer type indicating the end of a brew

cycle. They are Burst (a series of burst), None, Steady, Single Pulse or Double

Pulse. Use the select key to make your selection. Select None to disable the

When enabled this option allows a short audible tone to be sounded whenever a

key is depressed to provide audible reassurance that the button was indeed

pressed and the function initiated. Select Yes to enable and No to disable this

This feature allows you to program in the number of brew cycles which you want to

run before the brewer automatically displays the "* Call For Service *" message so

that routine maintenance may be performed. The brewer will continue to oper-ate

After programing the Service Cycles this message will prompt you to exit the

program/service mode. Select Yes to exit the program mode. If you select No you

will be returned to the Program/Service menu at which time you may select

- 5 -