Hi-Force HAP21022 Series Gebrauchsanweisung
Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Water Pump Hi-Force HAP21022 Series herunter. Hi-Force HAP21022 Series 8 Seiten. Air driven hydraulic pumps
Auch für Hi-Force HAP21022 Series: Gebrauchsanweisung (8 seiten)
Seite drucken
INSTRUCTION MANUAL – AIR DRIVEN HYDRAULIC PUMPS:
Model Series: AHP1120, AHP1120R, AHP1121, AHP1121R, AHP1122, AHP1122R, AHP1141, AHP1142,
HAP21011, HAP21012, HAP21014, HAP21016, HAP21021, HAP21022, HAP21024, HAP21026, HAP21031,
HAP21032, HAP21034, HAP21036, HAP21041, HAP21042, HAP21044, HAP21046,
NOTE: Spare parts sheets for these products are
available from the Hi-Force website at:
www.hi-force.com
or from your local regional Hi-Force Sales office
or authorized local Hi-Force distributor.
1.0 Inspection of the product upon receipt:
On receipt of the product, visually inspect the
item for any evidence of shipping damage.
Please note shipping damage is not covered
by warranty. If shipping damage is found notify
the carrier immediately and refrain from putting
the product into service. The carrier is
responsible for repair and replacement costs
resulting from damage in transit shipment.
2.0 Safety Precautions:
Read and follow all the instructions and safety
warnings
carefully
prior
equipment. Failure to do so could result in
equipment
damage
or
equipment or personal injury. Hi-Force will not
be held responsible for any damage to the
equipment or personal injury resulting from
unsafe
use
of
the
product,
maintenance or incorrect operation. If in doubt
on
the
correct
usage
equipment, contact your nearest Hi-Force
office or distributor. If the operator has not
been
trained
on
high pressure
equipment and its safe use consult your local
Hi-Force sales office who can offer you training
courses for operators.
All operators should ensure that all necessary
personal protective equipment as specified by
their employer is worn when operating any
hydraulic equipment. Safety shoes, safety
glasses/ visor and
protective gloves should be
worn at all times. All relevant risk assessments
should be completed prior to use of the
equipment
.
Hi‐Force Limited – Prospect Way – Daventry – Northants NN11 8PL – United Kingdom
Tel: +44(0) 1327 301000: Fax: +44(0) 1327 706555: Website: www.hi‐force.com
manual pumps MUST be rated for use at the
same operating pressure as the pump model to
be used:-
Models AHP1120 up to and including AHP1142 –
Max working Pressure - 700bar (10,000psi)
Models HAP21011 up to and including
HAP21046 – Max working Pressure - 700bar
(10,000psi)
sure that all the components are fit for the
intended use.
pump reservoir to fully operate the system to be
used.
system to be used. Under no circumstances
ever tamper with the internal safety relief valve
of the pump.
Hydraulic pumps must only be serviced by a
qualified technician.
To protect your warranty, only use Hi-Force's
to
use
of
the
hydraulic oil.
Immediately replace any worn or damaged
failure
of
the
parts using genuine Hi-Force parts only.
The system operating pressure must not exceed
the pressure rating of the lowest component in
the system. Where possible, use a pressure
lack
of
gauge to monitor the system.
Avoid damaging hydraulic hose. Always route
of
any
Hi-Force
hoses to ensure that they are free from sharp
bends and kinks. Using a bent or kinked hose
will cause severe back-pressure and can also
hydraulic
lead to the failure of the hose.
ruptured hose can penetrate the skin and lead
to a serious medical emergency and in certain
cases death. Should this incident happen
medical attention must be sought immediately.
Warning: All ancillary equipment to be
used with these ranges of hydraulic
Sufficient time should be allocated to
planning your hydraulic system. Make
Ensure there is sufficient oil capacity in the
DO NOT exceed the rated pressure of the
pump or the rated capacity of the
Keep hydraulic pumps away from flames
and direct heat.
Never
lift
or
carry
any
components by the hose or hoses
connected to them.
Do not handle a pressurized hydraulic
hose. Oil escaping under pressure from a
hydraulic