Hi-Force HP110 Gebrauchsanweisung

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Water Pump Hi-Force HP110 herunter. Hi-Force HP110 6 Seiten. Manually operated hydraulic pump - steel
Auch für Hi-Force HP110: Gebrauchsanweisung (4 seiten), Betriebsanleitung (13 seiten)

Seite drucken

Model Series: HP110, HP227-257, HP211-252D, HPX1500-2800

NOTE: Spare parts sheets for these products are

available from the Hi-Force website at:

www.hi-force.com

or from your local regional Hi-Force Sales office

or authorized local Hi-Force distributor.

1.0 Inspection of the product upon receipt:

On receipt of the product, visually inspect the

item for any evidence of shipping damage.

Please note shipping damage is not covered

by warranty. If shipping damage is found notify

the carrier immediately and refrain from putting

the product into service. The carrier is

responsible for repair and replacement costs

resulting from damage in transit shipment.

2.0 Safety Precautions:

Read and follow all the instructions and safety

warnings carefully prior to use of the equipment.

Failure to do so could result in equipment

damage or failure of the equipment or personal

injury. Hi-Force will not be held responsible for

any damage to the equipment or personal

injury resulting from unsafe use of the product,

lack of maintenance or incorrect operation. If in

doubt on the correct usage of any Hi-Force

equipment, contact your nearest Hi-Force office

or distributor. If the operator has not been

trained on high pressure hydraulic equipment

and its safe use consult your local Hi-Force sales

office who can offer you training courses for

operators.

All operators should ensure that all necessary

personal protective equipment as specified by

their employer is worn when operating any

hydraulic equipment. Safety shoes, safety

glasses/ visor and protective gloves should be

worn at all times. All relevant risk assessments

should be completed prior to use of the

equipment

Hi-Force Limited – Prospect Way – Daventry – Northants NN11 8PL – United Kingdom

Tel: +44(0) 1327 301000: Fax: +44(0) 1327 706555: Website: www.hi-force.com

INSTRUCTION MANUAL – HYDRAULIC HAND PUMPS:

Warning: All ancillary equipment to be

used with these ranges of hydraulic

manual pumps MUST be rated for use at the

same operating pressure as the pump model to

be used:-

HP110 – 700bar (10,000psi)

HP227 – HP257 – 700 bar (10,000psi)

HP211, HP212, HP232, HP252–700 bar (10,000psi)

HP232D, HP252D – 700 bar (10,000 psi)

HP245 – HP245D – 700 bar (10,000 psi)

HPX1500 – 1500 bar (21,755 psi)

HPX2800 – 2800 bar (40,610 psi)

Sufficient time should be allocated to

planning your hydraulic system. Make

sure that all the components are fit for the

intended use.

Ensure there is sufficient oil capacity in

the pump reservoir to fully operate the

system to be used.

DO NOT exceed the rated pressure of the

pump or the rated capacity of the

system to be used. Under no circumstances

ever tamper with the internal safety relief valve

of the pump.

Keep hydraulic pumps away from flames

and direct heat.

Hydraulic pumps must only be serviced by a

qualified technician.

To protect your warranty, only use Hi-Force's

hydraulic oil.

Immediately replace any worn or damaged

parts using genuine Hi-Force parts only.

The system operating pressure must not exceed

the pressure rating of the lowest component in

the system. Where possible, use a pressure

gauge to monitor the system.

Avoid damaging hydraulic hose. Always route

hoses to ensure that they are free from sharp

bends and kinks. Using a bent or kinked hose will

cause severe back-pressure and can also lead

to the failure of the hose.

Never

lift

components by the hose or hoses

connected to them.

Do not handle a pressurized hydraulic

hose. Oil escaping under pressure from a

ruptured hose can penetrate the skin and lead

to a serious medical emergency and in certain

cases death. Should this incident happen

medical attention must be sought immediately.

carry

any

hydraulic