Gaggenau VG 231 AU Einbauanleitung - Seite 4

Blättern Sie online oder laden Sie pdf Einbauanleitung für Kochfeld Gaggenau VG 231 AU herunter. Gaggenau VG 231 AU 4 Seiten. Gas cooker
Auch für Gaggenau VG 231 AU: Betriebs- und Montageanleitung (19 seiten)

Seite drucken

Fitting the appliance

Mark the centre of the recess exactly. Fit the mounting rails to

the front and rear of the recess. Make sure the lugs of the

mounting rails lie on the worktop. The centre marking on the

mounting rails must be precisely flush with the centre marking

of the recess.

Note. when fitting the appliance in a stone worktop glue on the

mounting rails with a temperature-resistant two-component

adhesive (metal on stone).

For combination with the appliance cover VD 201: secure the

appliance cover on the appliance before installation (refer to

the installation manual of VD 201).

Lower the appliance into the cut-out. The snap-in pins on the

appliance must lie exactly on the catch springs. Firmly press

the appliance into the cut-out. The pins on the appliance must

snap into the catch springs.

Removing the appliance

Disconnect the appliance from the power and the gas supply.

Push out the appliance from below.

Caution!

Risk of damage! Do not lever out the appliance from above.

Gas connection

The supply connection point shall be accessible with the

appliance installed.

Using the R½'' (for appliance side) connection elbow provided,

connect the appliance with the associated gasket to a fixed

connection pipe. For natural gas the regulator must be

connected.

If using a flexible connection

This appliance is approved for connection by a CLASS B hose.

Connection is in compliance with AS/NZS 5601.1

There are two ways to carry out the connection to the main gas

line:

A: The hotplate can be connected with rigid pipe.

■

B: Flexible Hose: If installing with a hose assembly, install with

■

a hose assembly that complies with AS/NZS 1869 (AGA

Approved), 10 mm ID, class Bor D, no more than 1.2 m long

and in accordance with AS/NZS 5601.1. Ensure that the hose

does not contact the hot surfaces of the hotplate, oven,

dishwasher or any other appliance that may be installed

underneath or next to the hotplate. The hose should not be

subjected to abrasion, kinking or permanent deformation and

should be inspected along its entire length with the cooktop in

the installed position. Unions compatible with the hose fittings

must be used and all connections tested for gas leaks.

Before leaving - check all connections for gas leaks with soap

and water. DO NOT use a naked flame for detecting leaks.

Ignite all burners both individually and concurrently to ensure

correct operation of gas valves, burners and ignition. Turn gas

taps to low position and observe stability of the flame for each

burner individually and all together.

Adhere the duplicate data plate to an accessible location near

to the cook top. When satisfied with the cook top, please

instruct the user on the correct method of operation. In case the

appliance fails to operate correctly after all checks have been

carried out, refer to the authorised service provider in your area.

Electrical connection

Check that the appliance has the same voltage and frequency

as the electrical installation system.

The hob is delivered with a mains cable and 3 pin moulded

plug.

Only connect the appliance to sockets which have been fitted

and earthed according to regulations.

The appliance corresponds to type Y: the mains connection

cable must only be replaced by the after-sales service. Check

the cable type and minimum cross section.

Technical data / nozzle table

Total connected load electric 0.8 VA

Nozzle table

Gas

Natural Gas

Pressure

1.0 kPa

C Nozzle, full burn, outer

195

A Nozzle, low burn, outer

D Nozzle, full burn, inner

B Nozzle, low burn, inner

Air gap adjustment, outer

0 mm

Total connected load

18.0 MJ (5 kW)

Total consumption

0.47 m³/h

Conversion to another type of gas

This gas hob corresponds to the categories specified on the

rating plate. It is possible to convert the appliance to any of the

gases listed on the plate by changing the nozzles. The

modification kit can be ordered via our after-sales service.

Depending on the model the parts required may beincluded in

the scope of delivery.

The conversion must be carried out by an authorised person.

Before carrying out the conversion, turn off the electricity and

gas supply.

Changing the low burn nozzle:

Remove pan support and all burner parts.

Unscrew two fastening screws (Torx T20) and remove

stovetop.

Remove control knob. Remove control panel: Unscrew the two

upper, lateral fastening screws (Torx T20). Raise control panel

in the rear and push it forward. Remove switch cover.

The low burn nozzle is located in the gas valve and is screwed

in from above. For easier accessibility, turn switch or remove

securing ring and remove switch. Unscrew the nozzle and

insert the new nozzle as specified in the low-setting nozzle

table. The nozzle must be screwed in fully.

Put switch, securing ring, switch cover and control panel back

in place and screw them tight. Put on control knob

Changing the full burn nozzle:

Remove securing clips on the burner pipes. Remove burner

pipes. Loosen screw on air-regulating tube. Remove nozzle

fitting

Remove nozzle and O-ring for inner circular burner by hand.

Unscrew nozzle for outer circular burner (SW10).

Check that O-ring is correctly positioned in new full-burn nozzle

for inner circular burner. Push nozzle onto burner pipe. Screw

new main nozzle for outer circular burner all the way into nozzle

fitting.

Put on nozzle fitting and burner pipes. Put on securing clips.

Set air-regulating tube to correct dimension after loosening the

screw (see nozzle table). Tighten screw again.

Put stovetop in place and screw it tight. Put burner parts and

pan support in place, positioning them correctly.

If it should be necessary to correct the low-setting nozzle as the

result of deviating gas types and pressure, the flow rate can be

increased by turning to the left.

These burners do not require the primary air to be adjusted.

Checking functions after the conversion:

The flames are adjusted correctly if no yellow tips are visible

and if they do not go out when switching over swiftly from the

high to the low setting.

Note. stick the adhesive label included with the nozzle set over

the rating plate of the appliance to document the changeover to

a different gas type.

Propane Gas

2.75 kPa

110

0 mm

18.0 MJ (5 kW)

376 g/h