Gaggenau VG 233 234 CN Einbauanleitung - Seite 4

Blättern Sie online oder laden Sie pdf Einbauanleitung für Kochfeld Gaggenau VG 233 234 CN herunter. Gaggenau VG 233 234 CN 4 Seiten.

Seite drucken

Ú Installation instructions

Important notes

Read these instructions carefully and keep them in a safe place.

Safety during use can only be ensured if the appliance is fitted

correctly according to these installation instructions. The installer

is responsible for ensuring that the appliance operates perfectly at

the point of installation.

The appliance must be connected to the mains only by a licensed

and trained technician.

Before carrying out any type of work, turn off the electricity and gas

supply.

For installation, currently applicable building regulations and the

regulations of local electricity and gas suppliers must be observed.

For conversion to another type of gas, please call the after-sales

service.

Risk of gas escape!

After connecting the appliance to the gas supply, always check the

connection for leak tightness. The manufacturer accepts no

responsibility for the escape of gas from a gas connection which

has been previously tampered with.

Ensure sufficient air exchange in the room where the appliance is

installed. Up to 11 kW total output:

Minimum volume of the room where appliance is installed: 20 m³

■

A door leading to the open air or a window which can be opened.

■

Up to 18 kW total output:

Minimum volume of the room where appliance is installed: 2 m³

■

per kW total output.

A door leading to the open air or a window which can be opened.

■

An extraction hood into the open air. Minimum displacement

■

volume of extraction hood: 15 m³/h per kW total output.

The installation system must incorporate an all-pin isolating switch

with a contact opening of at least 3 mm, or the appliance should be

connected to the mains via a safety plug. The plug must remain

accessible after installation is complete.

Specifications on the rating plate showing voltage, type of gas and

gas pressure must agree with the local mains connection

conditions.

Do not kink or trap the mains connection cable.

This appliance corresponds to appliance class 3 (for installation in

a kitchen unit). It must be fitted according to the installation

drawing. The wall behind the appliance must be made of non-

flammable material.

This appliance is not intended for operation with an external timer

or an external remote control.

Do not install this appliance on boats or in vehicles.

Preparing the furniture

The surrounding kitchen unit must be heat-resistant to at least

90 °C. The stability of the unit must be maintained after producing

the cut-out.

Produce the cut-out for the appliances. Proceed as shown in the

installation sketch. The dimensions in the installation sketch allow

for the additional space required for the connecting strip. The

angle between the cut surface and the worktop must be 90°.

After producing the cut-out, remove the shavings. Seal the cut

surfaces to make them heat-resistant.

Observe a minimum clearance between the appliance housing

and parts of the unit of 10 mm.

The connecting strip VV 200 has to be ordered separately.

Appliances can also be fitted in individual recesses, if a minimum

clearance of 40 mm between the appliances is observed.

Fitting the appliance

Mark the distance to the centre of the appliances as shown in the

installation sketch. Fit the mounting rails to the front and rear of

the recess. Make sure the lugs of the mounting rails lie on the

worktop. The centre marking on the mounting rails must be

precisely flush with the centre markings of the recess.

Note: when fitting the appliance in a stone worktop glue on the

mounting rails with a temperature-resistant two-component

adhesive (metal on stone).

For combination with the appliance cover VD 201: secure the

appliance cover on the appliance before installation (refer to the

installation manual of VD 201).

Lower the first appliance into the cut-out. The snap-in pins on the

appliance must lie exactly on the catch springs. Firmly press the

appliance into the cut-out. The pins on the appliance must snap

into the catch springs.

Put the second appliance onto the securing rails and check that

the gap between the control panels is between 4.5 and 5.0 mm.

If the distance is not exactly right, take out the second appliance

again and loosen the screws of the installation rails. You can now

move the rails in the oblong holes. Then tighten the screws again.

Firmly press the second appliance onto the securing rails. Place

the connecting trim VV 200 between the appliances and press it

in (see installation guide of VV 200).

Removing the appliance

Disconnect the appliance from the power and the gas supply.

Push out the appliance from below.

Caution!

Risk of damage! Do not lever out the appliance from above.

Gas connection

The gas connection must be located in a position where the stop

tap is accessible.

Using one of the R½'' (for appliance side) connection elbows

provided, connect the appliance with the associated gasket to a

fixed connection pipe or a gas safety hose. If the gas safety hose

is not (or only partly) made of metal, the ambient temperature must

not exceed 70°K. In the case of a gas safety hose made entirely of

metal, the permissible ambient temperature is 115°K. The gas

safety hose must be routed so that it does not come into contact

with moving parts of the kitchen unit (e.g. drawers).

Electrical connection

Check that the appliance has the same voltage and frequency as

the electrical installation system.

The hob is delivered with a mains cable, with or without plug,

depending on model.

Only connect the appliance to sockets which have been fitted and

earthed according to regulations.

The appliance corresponds to type Y: the mains connection cable

must only be replaced by the after-sales service. Check the cable

type and minimum cross section.

Technical data

Wok burner:

Level 4 full burning (outer), full burning (inner)

5.2 kW(Hi) / 5.9 kW(Hs)

Level 3 low burning (outer), full burning (inner)

1.35 kW(Hi) / 1.5 kW(Hs)

Level 2 full burning (inner)

0.45 kW(Hi) / 0.5 kW(Hs)

Level 1 low burning (inner)

<0.23 kW(Hi) / 0.25 kW(Hs)

High-intensity burner:

Full burning

2.52 kW(Hi) / 2.80 kW(Hs)

Low burning

<0.50 kW(Hi) / 0.56 kW(Hs)

Normal burner:

Full burning

1.71 kW(Hi) / 1.90 kW(Hs)

Low burning

<0.34 kW(Hi) / 0.38 kW(Hs)

Gas connection:

R½" union nut for R½" bracket to DIN 1999, conical-cylindrical

Electric:

Rated consumption: 1.6 W

Voltage: 220 - 240 V

Frequency: 50 - 60 Hz

Technical modifications reserved.