Dynabrade 10729 Schnellstart-Handbuch - Seite 4

Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Sander Dynabrade 10729 herunter. Dynabrade 10729 4 Seiten. 8" 2-hand random orbital sander

Seite drucken

6. Install the 56586 Vacuum Plug into the exhaust passage of the housing. (See Exploded View)

7. Use needle-nose pliers to grasp and install the 51944 Tip Valve so that it fits under the 56579 Valve Stem.

8. Install the large end of the 51943 Spring into the air inlet passage of the handle.

9. Install the 56469 Gasket onto the mounting surface of the handle.

10. Install the 96459 O-Ring onto outside diameter of the air inlet passage at the location of the first shoulder and apply a small amount of petroleum lubricant to the o-ring.

11. Connect the handle to the housing and secure it in place with the four screws.

Note: The two longer screws, Part Number 96454 (2), also secure the 13160 Grip to the housing.

12. Install the 56597 Muffler and secure it in place with the 56596 Muffler Clip. (See Exploded View)

Handle and Valve Assembly Complete. Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.

Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the tool, the tool should

be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet with throttle lever depressed. Operate tool

for 30 seconds to determine if tool is operating properly and to allow lubricating oils to properly penetrate motor.

Loctite

is a registered trademark of Loctite Corp.

Drawing 1

57091

Bearing Press Tool

56589

Shaft

56133

Bearing

98221 Motor Tune-Up Kit

•

Includes assorted parts to

help maintain and repair motor.

96232 (#2) Arbor Press

•

This arbor press is ideal for the disassembly

and assembly of air motors.

96346 2" Bearing Separator

•

Use the separator to remove gears

and bearings.

95134 – 9/64" Hex Wrench

95135 – 5/32" Hex Wrench

96343 Retaining Ring Pliers

•

Internal/external retaining ring pliers.

Tip diameter - 0.038" (0.96mm)

Visit Our Web Site: www.dynabrade.com

DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524

DYNABRADE EUROPE S.àr.l.,

12/13

Diagrams

Drawing 2

57091

Bearing Press Tool

Front Bearing Plate

56133

Bearing

Optional Accessories

Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1

Drawing 3

54629

Rear Bearing Plate

56595

Cylinder

Front Bearing Plate

and Shaft

Dynabrade Air Lube

57325 Motor Repair Kit:

96213 Bearing Removal Tool

Email: [email protected]

Drawing 4

Bearing Press Tool

Cylinder w/Front

Bearing Plate

and Shaft

•

Formulated for pneumatic equipment.

•

Absorbs up to 10% of its weight in water.

•

Prevents rust and formation of sludge.

•

Keeps pneumatic tools operating longer

with greater power and less down time.

95842: 1pt. (473 ml)

95843: 1gal. (3.8 L)

• Contains special tools for

disassembly/assembly of machine.

•

This tool is used to pass through the I.D.

of the bearing plate and to push against

the I.D. of the bearing.

DYNABRADE

PRINTED IN USA

57091

01206

Bearing