Dynabrade 10764 Handbuch - Seite 4
Blättern Sie online oder laden Sie pdf Handbuch für Sander Dynabrade 10764 herunter. Dynabrade 10764 4 Seiten. 6"/8" pad, 3/16" orbit, non-vac/central vac, 900 rpm air motor and machine parts
Seite drucken3. Install the 98459 O-Ring onto the 56579 Valve Stem, apply a small amount of petroleum lubricant to the o-ring and insert the shortest portion (from the end to the o-ring) of
the valve stem assembly into the speed regulator.
4. Install the 56582 Safety Throttle Lever onto the housing and secure it in place with the 95627 Pin.
5. Install the 56598 Seal into the air inlet passage of the housing.
6. Install the 56586 Vacuum Plug into the exhaust passage of the housing. (See Exploded View)
7. Use needle-nose pliers to grasp and install the 51944 Tip Valve so that it fits under the 56579 Valve Stem.
8. Install the large end of the 51943 Spring into the air inlet passage of the handle.
9. Install the 56469 Gasket onto the mounting surface of the handle.
10. Install the 96459 O-Ring onto outside diameter of the air inlet passage at the location of the first shoulder and apply a small amount of petroleum lubricant to the o-ring.
11. Connect the handle to the housing and secure it in place with the four screws. Note: The two longer screws, Part Number 96454 (2) secure the 56581 Grip to the housing.
12. Install the 56597 Muffler and secure it in place with the 56596 Muffler Clip. (See Exploded View)
Handle and Valve Assembly Complete. Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important: Motor should now be tested for proper operation at 90 PSIG. If motor does not operate properly or operates at a higher RPM than marked on the tool, the tool should
be serviced to correct the cause before use. Before operating, place 2-3 drops of Dynabrade Air Lube (P/N 95842) directly into air inlet with throttle lever depressed. Operate tool
for 30 seconds to determine if tool is operating properly and to allow lubricating oils to properly penetrate motor.
Loctite
®
is a registered trademark of Loctite Corp.
Drawing 1
57091
Bearing Press Tool
56589
Shaft
56133
Bearing
98221 Motor Tune-Up Kit
•
Includes assorted parts to
help maintain and repair motor.
96232 (#2) Arbor Press
•
This arbor press is ideal for the disassembly
and assembly of air motors.
96346 2" Bearing Separator
•
Use the separator to remove gears
and bearings.
95134 – 9/64" Hex Wrench
95135 – 5/32" Hex Wrench
96401 – 2mm Hex Wrench
96343 Retaining Ring Pliers
•
Internal/external retaining ring pliers.
Tip diameter - 0.038" (0.96mm)
Visit Our Web Site: www.dynabrade.com
DYNABRADE, INC., 8989 Sheridan Drive • Clarence, NY 14031-1490 • Phone: (716) 631-0100 • Fax: 716-631-2073 • International Fax: 716-631-2524
DYNABRADE EUROPE S.àr.l.,
© DYNABRADE, INC., 2013
Diagrams
Drawing 2
57091
Bearing Press Tool
Front Bearing Plate,
Lock Ring and
Pinion Gear
56133
Bearing
Optional Accessories
Zone Artisanale • L-5485 Wormeldange—Haut, Luxembourg • Telephone: 352 76 84 94 1 • Fax: 352 76 84 95 1
Drawing 3
54629
Rear Bearing Plate
56495
Cylinder
Front Bearing Plate,
Lock Ring,
Pinion Gear
and Shaft
02695 Bearing
Email: [email protected]
Drawing 4
Bearing Press Tool
Cylinder w/Front
Bearing Plate,
Lock Ring,
Pinion Gear
Dynabrade Air Lube
•
Formulated for pneumatic equipment.
•
Absorbs up to 10% of its weight in water.
•
Prevents rust and formation of sludge.
•
Keeps pneumatic tools operating longer
with greater power and less down time.
95842: 1pt. (473 ml)
95843: 1gal. (3.8 L)
96283 Motor Repair Kit:
• Contains special tools for
disassembly/assembly of machine.
96213 Bearing Removal Tool
•
This tool is used to pass through the I.D.
of the bearing plate and to push against
the I.D. of the bearing.
DYNABRADE
PRINTED IN USA
57091
01206
Bearing
and Shaft
®