Hi-Tech SHAVGS05 Schnellstart-Handbuch - Seite 2

Blättern Sie online oder laden Sie pdf Schnellstart-Handbuch für Sicherheitssystem Hi-Tech SHAVGS05 herunter. Hi-Tech SHAVGS05 2 Seiten. Visible signaling appliance

Seite drucken

IV. WIRING

Wiring for synchronized strobes and horns.

Using this method you may:

w Use only two wires to synchronize the temporal horn and strobe with the ability to mute the horn (place

switches 1 and 2 in the ON position on the SHAVGS07.

w Mute the horn only when the temporal horn option has been selected.

w Use the Safety Hi-Tech synchronization protocol to provide synchronization and mute the horn, if

available.

Wiring for synchronized parallel (unison) horn/strobe operation.

Using this method you may:

w Use four wires where two wires are used to power and synchronize the strobe and two additional wires

are used to power and synchronize the horn (place switches 1 and 2 in the OFF position on the \

SHAVGS07.

w Choose either continuous horn and allow the FACP to control the horn or choose temporal horn and

synchronize the horns with the Safety Hi-Tech synchronization protocol.

CAUTION: When using only a single power source to energize the strobe and horn (switches 1 and 2 in the ON position), the

in/out wiring must be under the S+ and S- terminals only. Failure to do so may result in damage to your signal. For the

SHAVGS05, only the top three terminals are to be used.

CAUTION: A jumper card is provided to

test for correct wiring in the supervisory

mode only. DO NOT pass alarm current

through the jumper.

THIS APPLIANCE WILL NOT OPERATE WITHOUT ELECTRICAL POWER. AS FIRES FREQUENTLY

CAUSE POWER INTERRUPTIONS, SAFETY HI-TECH SUGGESTS YOU DISCUSS FURTHER

SAFEGUARDS WITH YOUR LOCAL FIRE PROTECTION SPECIALIST.

V. CHECKOUT AND TROUBLESHOOTING

1. Supply power to the system control panel. The auxiliary signaling appliances in the system should not

be activated.

2. If the signal is activated:

w Check all smoke and fire detectors in the system to make sure they have not been activated.

w Check all wiring connections to make sure the signal detection circuits are not reversed or shorted

together. Check wire color codes and traces.

3. To test the signal appliances, trip the auxiliary panel or activate the alarm circuit at the main control

panel or activate one of the fire detection units in the system. All auxiliary signals should be activated.

4. An operational test on this product should be conducted in accordance with National Standards or at a

minimum annually and more often if dictated by local and state codes or authorities having jurisdiction.

NOTICE: THESE TESTING PROCEDURES AND TROUBLESHOOTING INSTRUCTIONS ARE

GENERALIZED. PLEASE REFER TO THE SYSTEM CONTROL PANEL OPERATING INSTRUCTIONS FOR

PROPER OPERATION OF THE PANEL AND FIRE DETECTION SYSTEM.

For a period of 36 months from the date of purchase or a maximum of 42 months from the date of manufacture (or as long as required by applicable law), Safety Hi-Tech warrants to you the original purchaser that your

appliance will be free from defects in workmanship and materials under normal use and service.

This warranty does not apply and is void if damage or failure is caused by: accident, abuse, misuse, abnormal use, faulty installation, liquid contact, fire, earthquake or other external cause; operating the appliance outside

Safety Hi-Tech's published guidelines; or service, alteration, maintenance or repairs performed by anyone other than Safety Hi-Tech. This warranty also does not apply to: consumable parts, such as batteries; cosmetic

damage, including but not limited to scratches or dents; defects caused by normal wear and tear or otherwise due to the normal aging of the appliance, or if any serial number has been removed or defaced from the

appliance.

TO THE EXTENT PERMITTED BY LAW, THIS WARRANTY AND THE REMEDIES SET FORTH HEREIN ARE EXCLUSIVE AND IN LIEU OF ALL OTHER WARRANTIES, REMEDIES AND CONDITIONS, WHETHER

ORAL, WRITTEN, STATUTORY, EXPRESS OR IMPLIED. SAFETY HI-TECH DISCLAIMS ALL STATUTORY AND IMPLIED WARRANTIES, INCLUDING WITHOUT LIMITATION, WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE AND WARRANTIES AGAINST HIDDEN OR LATENT DEFECTS TO THE EXTENT PERMITTED BY LAW. TO THE EXTENT SUCH WARRANTIES CANNOT BE

DISCLAIMED, SUCH IMPLIED WARRANTIES SHALL APPLY ONLY FOR THE WARRANTY PERIOD SPECIFIED ABOVE. PLEASE NOTE THAT SOME STATES (COUNTRIES AND PROVINCES) DO NOT ALLOW

LIMITATION ON HOW LONG AN IMPLIED WARRANTY (OR CONDITION) LASTS. SO THE ABOVE LIMITATION MAY NOT APPLY TO YOU.

EXCEPT AS PROVIDED IN THIS WARRANTY AND TO THE EXTENT PERMITTED BY LAW, SAFETY HI-TECH WILL NOT BE LIABLE FOR ANY DIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES

RESULTING FROM ANY BREACH OF WARRANTY OR CONDITION, OR ARISING IN CONNECTION WITH THE SALE, USE OR REPAIR OF THE APPLIANCE, OR UNDER ANY OTHER LEGAL THEORY, INCLUDING

BUT NOT LIMITED TO LOSS OF USE, LOSS OF REVENUE, LOSS OF ACTUAL OR ANTICIPATED PROFITS, LOSS OF THE USE OF MONEY, LOSS OF BUSINESS, LOSS OF OPPORTUNITY, LOSS OF GOODWILL,

AND LOSS OF REPUTATION. THE MAXIMUM LIABILITY OF SAFETY HI-TECH SHALL NOT IN ANY CASE EXCEED THE PURCHASE PRICE PAID BY YOU FOR THE APPLIANCE. PLEASE NOTE THAT SOME

STATES (COUNTRIES AND PROVINCES) DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO

YOU.

If a defect in workmanship or materials causes your appliance to become inoperable within the warranty period, you must return the appliance to Safety Hi-Tech postage prepaid to: Safety Hi-Tech, Via Cavour, 96,

67051Avezzano L'Aquila, Italy. You must prove to the satisfaction of Safety Hi-Tech the date of purchase of your appliance. You must also enclose a return address. Warranty service may only be performed by Safety

Hi-Tech personnel at Safety Hi-Tech's facilities in Avezzano L'Aquila, Italy. You must also pack the appliance to minimize the risk of it being damaged in transit. If we receive an appliance in a damaged condition as the

result of shipping, we will notify you and you must seek a claim with the shipper.

If you submit a valid claim toSafety Hi-Tech during the warranty period, Safety Hi-Tech will, at its option, repair your appliance or furnish you with a new or rebuilt appliance without charge to you except for postage required

to return the appliance to us. Safety Hi-Tech will not reimburse you for repairs or replacement parts provided by other parties. Your repaired or replacement appliance will be returned to you free of charge and it will be

covered under the warranty for the balance of the warranty period, if any. When a product or part is replaced, any replacement item becomes your property and the replaced item becomes property of Safety Hi-Tech.

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE (OR BY COUNTRY OR PROVINCE). BY THIS WARRANTY,

SAFETY HI-TECH DOES NOT LIMIT OR EXCLUDE YOUR RIGHTS EXCEPT AS ALLOWED BY LAW. TO FULLY UNDERSTAND YOUR RIGHTS, YOU SHOULD CONSULT THE LAWS OF YOUR COUNTRY,

PROVINCE OR STATE.

LIMITED WARRANTY

w Use the Safety Hi-Tech synchronization protocol to provide synchronization and mute the horn, if

available.

NOTICE:

w FOR THIS OPTION, SWITCHES 1 AND 2 ON THE SHAVGS07 MUST BE IN THE OFF POSITION TO

ISOLATE POWER TO THE AUDIBLE AND VISIBLE PORTION OF THE CIRCUIT.

w ALL STROBES ARE DESIGNED TO FLASH AS SPECIFIED WITH CONTINUOUS APPLIED VOLTAGE

THIS APPLIANCE IS NOT RECOMMENDED FOR USE ON CODED OR PULSING SIGNALING

CIRCUITS.

Conventional Method:

You may connect both the strobe and the horn directly from a source of rated power without the use of a

control module. However, the horns and strobe lights will NOT be synchronized. Place switches 1 and 2 in

the ON position on the SHAVGS07 to power both the audible and visible from a single pair of power wires. If

you wish to power the horn and strobe from independent sources of power, place switches 1 and 2 in the

OFF position on the SHAVGS07 and connect power to the appropriate terminals.

TONE

Mechanical Temporal 3

Mechanical - Continuous

2400Hz - Temporal 3

2400Hz - Continuous

Chime - Temporal 3

Chime - Continuous

Whoop

Candela selection

slider switch. Depress

center and slide switch

to desired

brightness level.

Break off pin and insert

into hole at the bottom

of the selector to lock

candela setting. Signal

must be removed from

bracket and pin pushed

forward from backside

out of hole to change

candela.

Mounting Bracket: Allows the installer to pre-wire the system, test for system supervision, remove the

signal head until occupancy, switch out Safety Hi-Tech signals without changing mounting brackets and

has locking edge connector for snap-in-place installation.

Instant Voltage Verification:

It is often necessary to confirm the voltage drop along a line of devices. The access holes are provided in

the back of the terminal block to allow the voltage to be measured directly without removing the device.

Typically this would be done at the end of the line to confirm design criteria. Most measurements will be

taken using the S+ and S- locations although access is provided to other locations.

NOTICE: CARE SHOULD BE TAKEN TO NOT SHORT THE TEST PROBES.

SIGNALING APPLIANCE LIMITATION:

Your horn and horn/strobe meet or exceed the current audibility requirements of ANSI/UL 464. However, if

the appliance is located outside a bedroom it may not wake up a sound sleeper, especially if the room door is

closed or only partially open.

VI. TO RETURN AN APPLIANCE

Should you experience problems with your appliance, proceed as follows:

1. Turn off electrical power to the auxiliary alarm circuit.

2. Remove the bezel, nameplate, then mounting screw and slide signal off from bracket

3. Replace unit that was removed to restore wiring supervision and to eliminate system trouble alert.

4. Carefully pack the defective unit (the manufacturer cannot be responsible for consequential damage due

to shipping or mis-handling). Include a return address and complete details as to the nature of the

difficulties being experienced and date of installation.

5. Return to: Safety Hi-Tech, Via Cavour, 96-67051 Avezzano L'Aquila, ITALY. Prior to returning, call

Safety Hi-Tech at +39.0863.19407.20 to obtain a RMA Number from our Customer Service Department.

SWITCH POSITION

NOTICE:

w SWITCH POSITIONS 1

AND 2 IN THE OFF

OFF

POSITION TO SELECT

ISOLATED HORN AND

OFF

STROBE POWER

OFF

INPUTS

OFF

w SWITCH POSITION 6

OFF

ON = HIGH dBA

w SWITCH POSITION 6

OFF

OFF = LOW dBA

OFF

To remove bezel, grip both sides of bezel

and pull in a downward and outward motion.

SAFETY HI-TECH

VIA CAVOUR, 96

67051 AVEZZANO L'AQUILA, ITALY

PHONE: +39.0863.19407.20

www.safetyhitech.com

Important Notice:

These materials have been prepared by Safety Hi-Tech for informational purposes

only, are necessarily summary, and are not purported to serve as legal advice and

should not be used as such. Safety Hi-Tech makes no representations and

warranties, express or implied, that these materials are complete and accurate,

up-to-date, or in compliance with all relevant local, state and federal laws, regulations

and rules. The materials do not address all legal considerations as there is inevitable

uncertainty regarding interpretation of laws, regulations and rules and the application

of such laws, regulations and rules to particular fact patterns. Each person's activities

can differently affect the obligations that exist under applicable laws, regulations or

rules. Therefore, these materials should be used only for informational purposes and

should not be used as a substitute for seeking professional legal advice. Safety

Hi-Tech will not be responsible for any action or failure to act in reliance upon the

information contained in this material.

550-0621-AAA

12/17/13

Page 2