Dynabrade 52716 Sicherheit, Betrieb und Wartung - Seite 6
Blättern Sie online oder laden Sie pdf Sicherheit, Betrieb und Wartung für Schleifer Dynabrade 52716 herunter. Dynabrade 52716 8 Seiten. 1hp cone or plug grinder governor controlled
Seite drucken
Assembly Instructions - (Continued)
Important: Manufacturer's warranty is void if tool is disassembled before warranty expires.
Please refer to parts breakdown for part identification.
10.
51924
Peel backing off
11.
51923
Place
Rear Bearing Plate over rotor mandrel and insert raised boss on rear bearing plate into cylinder diameter, while
inserting short coiled pin into cylinder slot. Be sure inlet slot on rear bearing plate line up with inlet slot on cylinder. Flip
cylinder end to end and repeat steps 8 & 9 for correct assembly.
12.
02057
Press
Bearing onto rotor and into
Important:
While pressing
between bearing plates. If too tight, rotor will not turn freely. Rotor must be lightly tapped at press fit end until rotor spins
freely while still maintaining a snug fit. A loose fit will not achieve the proper preload on motor bearings.
13.
Add one drop of Loctite
HAND
thread) with a slotted screw head. Torque to 2 N•m (18 lb.-in.).
14.
Install motor assembly into housing, making sure motor drops all the way into housing.
to slots in insert and against
15.
95438
Install
O-Ring onto
16.
96498
Place
Wave Washer onto
17.
Apply a small amount of Loctite
separately ) or an adjustable pin wrench. Torque cover to 35 N•m (310 lb.-in.).
Motor Assembly Complete.
1.
Secure housing using
2.
51945
Install
Valve Seat by aligning 3 male prongs with three deep slots on insert. Make certain valve seat is pressed flat
against base of pocket.
Note:
Add a few drops of Dynabrade Air Lube (P/N
3.
51944
Install
Tip Valve as shown.
4.
51942
Slide
Baffle into housing long end in first, and place
5.
51937
Pre-assemble
into groove at the base of thread. Slide
6.
Apply one drop of Loctite
7.
Align small inside diameter of
assembly into place. Torque bushing to 35 N•m (310 lb.-in.).
8.
96443
Slide
O-Ring onto
valve stem assembly slides freely after the o-ring passes through the hole.
9.
Remove housing from
the bench. Align the throttle lever holes to housing pin hole and rest the housing and throttle lever onto the legs of the repair
96444
collar. Press
Tool Assembly Complete. Please allow 30 minutes for adhesives to cure before operating tool.
Important:
Before operating, places 2-3 drops of Dynabrade Air Lube (P/N
depressed. Operate tool for 30 seconds to allow Air Lube to properly lubricate internal motor components. Motor should now be
tested for proper operation at 90 PSIG max. If tool operates at a higher RPM than marked on the tool or if vibration and sound
levels seem abnormal, the tool should be serviced to correct the cause before use.
Loctite
is a registered trademark of Loctite Corp.
®
Gasket and align it firmly in place onto
51923
02057
Bearing, make certain to contact inner race of bearing only. Cylinder must fit snug
243 (or equiv.) to governor assembly male thread and screw governor assembly into place (
®
51924
Gasket.
53620
Adapter and slide adapter into housing and over
53620
Adapter.
567 to housing thread, and install
®
51989
Repair Collar ( see back cover for Optional Accessories ) with spindle facing down.
51939
Inlet Bushing by sliding
51943
51937
243 (or equiv.) to
®
51943
Spring to cone point on
51946
Valve Stem and slide sub-assembly until o-ring passes through housing hole. Make certain
51989
Repair Collar and place repair collar onto the bench top with the part number identifier against
Coiled Pin into lever hole and center into housing.
51923
Rear Bearing Plate.
Rear Bearing Plate hole until it is seated.
51947
95842
) to pocket walls before inserting
51941
Spring into shallow wall end of baffle.
51940
Silencer Plate,
Spring into bushing and up to the two
Inlet Bushing thread.
51944
Tip Valve and thread
6
Note:
Align both
54520
Bearing.
50971
Housing Cover using
51945
Spacer over male thread and set
51938
Screens.
51937
Inlet Bushing and sub-
95842
) directly into inlet with throttle lever
LEFT
96445
Coiled Pins
Pin Wrench ( ordered
Valve Seal.
96442
O-Ring