Dynabrade 13460 Handbuch für Sicherheit, Betrieb und Wartung - Seite 3
Blättern Sie online oder laden Sie pdf Handbuch für Sicherheit, Betrieb und Wartung für Werkzeuge Dynabrade 13460 herunter. Dynabrade 13460 8 Seiten. 1hp right-angle. governor controlled 2,800 rpm and 2,800 rpm, versatility kit
Seite drucken
Important: A Preventative Maintenance Program is recommended whenever portable power tools are used. The program should include inspection of air
supply lines, air line pressure, proper lubrication and repair of tools. Refer to ANSI B186.1 for additional maintenance information.
• Use only genuine Dynabrade replacement parts to insure quality. To order replacement parts, specify Model#, Serial# and RPM of your air tool.
• All Dynabrade Rotary Vane air tools must be used with a Filter-Regulator-Lubricator to maintain all warranties. Dynabrade recommends the following:
11411 Air Filter-Regulator-Lubricator (FRL) – Provides accurate air pressure regulation and two stage filtration of water contaminants. Operates 55
SCFM/1,558 LPM @ 100 PSIG with 1/2" NPT female ports.
• Lubricate wick system through the angle gear oil fitting with 2-3 plunges for every 24
hours of use, to achieve maximum gear life. Important: Use only the recommended
angle gear oil for the wick system. Do not contaminate the wick with any other oil or
grease product (order 95848 Gear oil and 95541 Gun). Lubrication gun should be
upside down during lubrication. (See Fig.1)
• Grease the planetary gear assembly with the 95542 Grease by applying 2-3 plunges with
the 95541 Grease Gun after every 50 hours of use, achieve maximum gear life. (See Fig. 2)
• Dynabrade recommends one drop of air lube per minute for each 20 SCFM (example: if the tool specification states 40 SCFM, set the drip rate on the
filter-lubricator to 2 drops per minute). Dynabrade Air Lube (P/N 95842: 1 pt 473 ml) is recommended.
Routine Preventative Maintenance:
• Check free speed of right-angle Dynisher
of use or weekly, whichever occurs more frequently.
• DO NOT disassemble the governor for any reason. Reorder correct speed – governor assembly (See Assembly Breakdown) and recheck free speed of
tool with a tachometer.
• Mineral spirits are recommended when cleaning the tool and parts. Do not clean tool or parts with any solvents or oils containing acids, esters,
ketones, chlorinated hydrocarbons or nitro carbons.
• DO NOT clean or maintain tools with chemicals that have a low flash point (example: WD-40
• A Motor Tune-Up Kit (P/N 96532) is available which includes high wear and medium wear motor parts.
• Air tool labels must be kept legible at all times, if not, reorder label(s) and replace. User is responsible for maintaining specification information i.e.:
Model #, S/N, and RPM. (See Assembly Breakdown)
• Blow air supply hose out prior to initial use.
• Visually inspect air hoses and fittings for frays, visible damage and signs of deterioration. Replace damaged or worn components.
• Refer to Dynabrade's Warning/Safety Operating Instructions Tag (Reorder No. 95903) for safety information.
After maintenance is performed on tool, add a few drops of Dynabrade Air Lube (P/N 95842) to the air line and start the tool a few times to lubricate air motor.
Check for excessive tool vibration.
Handling and Storage:
• Use of tool rests and hangers are recommended.
• Protect tool inlet from debris (see Notice below).
• DO NOT carry tool by air hose.
• Protect abrasive accessories from exposure to water, solvents, high humidity, freezing temperature and extreme temperature changes.
• Store accessories in protective racks or compartments to prevent damage.
Model
Motor
Number
HP (W)
All Models
1 (746)
Additional Specifications: Air Inlet Thread 3/8" NPT • Hose I.D. Size 3/8" (10 mm) • Air Flow Rate Based At Max HP. • Air Pressure 90 PSIG Max
All Dynabrade motors use the highest quality parts and metals available and are machined to exacting tolerances. The failure of quality pneumatic motors
can most often be traced to an unclean air supply or the lack of lubrication. Air pressure easily forces dirt or water contained in the air supply into motor
bearings causing early failure. It often scores the cylinder walls and the rotor blades resulting in limited efficiency and power. Our warranty obligation is
contingent upon proper use of our tools and cannot apply to equipment which has been subjected to misuse such as unclean air, wet air or a lack of
lubrication during the use of this tool.
Following the reasonable assumption that any inherent defect which might prevail in a product will become apparent to the user within one year from the
date of purchase, all equipment of our manufacture is warranted against defects in workmanship and materials under normal use and service. We shall
repair or replace at our factory, any equipment or part thereof which shall, within one year after delivery to the original purchaser, indicate upon our
examination to have been defective. Our obligation is contingent upon proper use of Dynabrade tools in accordance with factory recommendations,
instructions and safety practices. It shall not apply to equipment which has been subject to misuse, negligence, accident or tampering in any way so as to
affect its normal performance. Normally wearable parts such as bearings, contact wheels, rotor blades, etc., are not covered under this warranty.
Maintenance Instructions
®
using a tachometer. This governor controlled right-angle Dynisher
Machine Specifications
Tool
Sound
Air Flow Rate
RPM
Level
CFM/SCFM (LPM)
2,800
80 dB(A)
6/42 (1201)
One Year Warranty
®
).
Air Pressure
Arbor Size
PSIG (Bars)
Inch (mm)
90 (6.2)
3/4 (19)
Notice
3
Fig.1
Fig.2
®
should be speed checked every 20 hours
Weight
Length
Pound (kg)
Inch (mm)
6 (2.6)
15 (381)
Height
Inch (mm)
7 (178)