GREAT PLANES Gee Bee Gebrauchsanweisung - Seite 13

Blättern Sie online oder laden Sie pdf Gebrauchsanweisung für Spielzeug GREAT PLANES Gee Bee herunter. GREAT PLANES Gee Bee 16 Seiten. Model aircraft great planes gee bee

Seite drucken

NEVER disassemble or modify the pack wiring in

any way or puncture the cells.

NEVER discharge below 2.5V per cell.

NEVER place the battery or charger on combustible

materials or leave it unattended during charge or

discharge.

ALWAYS KEEP OUT OF THE REACH OF CHILDREN.

NEVER charge the battery in the plane.

ALWAYS remove the battery from the plane after a

crash. Set it aside in a safe location for at least 20

minutes. If the battery is damaged in the crash it

could catch ﬁ re.

If the battery starts to swell, quickly move the battery to a safe

location, preferably outside. Place it in a bucket, covering the

battery with sand. Never use water to try and put out a LiPo ﬁ re.

AMA SAFETY CODE EXCERPTS

Read and abide by the following excerpts from the Academy

of Model Aeronautics Safety Code. For the complete Safety

Code refer to Model Aviation magazine, the AMA web site or

the Code that came with your AMA license.

General

1) I will not ﬂ y my model aircraft in sanctioned events, air shows,

or model ﬂ ying demonstrations until it has been proven to be

airworthy by having been previously, successfully ﬂ ight tested.

2) I will not ﬂ y my model aircraft higher than approximately

400 feet within 3 miles of an airport without notifying the

airport operator. I will give right-of-way and avoid ﬂ ying in the

proximity of full-scale aircraft. Where necessary, an observer

shall be utilized to supervise ﬂ ying to avoid having models ﬂ y

in the proximity of full-scale aircraft.

3) Where established, I will abide by the safety rules for the

ﬂ ying site I use, and I will not willfully and deliberately ﬂ y my

models in a careless, reckless and/or dangerous manner.

5) I will not ﬂ y my model unless it is identiﬁ ed with my name

and address or AMA number, on or in the model. Note: This

does not apply to models while being ﬂ own indoors.

7) I will not operate models with pyrotechnics (any device that

explodes, burns, or propels a projectile of any kind).

Radio Control

1) I will have completed a successful radio equipment ground

check before the ﬁ rst ﬂ ight of a new or repaired model.

2) I will not ﬂ y my model aircraft in the presence of spectators

until I become a qualified flier, unless assisted by an

experienced helper.

3) At all ﬂ ying sites a straight or curved line(s) must be

established in front of which all ﬂ ying takes place with the

other side for spectators. Only personnel involved with ﬂ ying

the aircraft are allowed at or in the front of the ﬂ ight line.

Intentional ﬂ ying behind the ﬂ ight line is prohibited.

4) I will operate my model using only radio control frequencies

currently allowed by the Federal Communications Commission.

5) I will not knowingly operate my model within three miles

of any pre-existing ﬂ ying site except in accordance with

the frequency sharing agreement listed [in the complete

AMA Safety Code].

9) Under no circumstances may a pilot or other person touch

a powered model in ﬂ ight; nor should any part of the model

other than the landing gear, intentionally touch the ground,

except while landing.

CHECK LIST

During the last few moments of preparation your mind may

be elsewhere anticipating the excitement of the ﬁ rst ﬂ ight.

Because of this, you may be more likely to overlook certain

checks and procedures that should be performed before the

model is ﬂ own. To help avoid this, a check list is provided to

make sure these important areas are not overlooked. Many

are covered in the instruction manual, so where appropriate,

refer to the manual for complete instructions. Be sure to

check the items off as they are completed (that's why it's

called a check list!).

❏

1. Check the C.G. according to the measurements provided

in the manual.

❏

2. Be certain the motor battery and receiver are securely

mounted in the fuse with hook and loop material.

❏

3. Balance your model laterally as explained in the

instructions.

❏

4. Use threadlocking compound to secure critical fasteners

such as the screws in the screw-lock pushrod connectors.

❏

5. Add a drop of oil to the axles so the wheels will turn freely.

❏

6. Conﬁ rm that all controls operate in the correct direction

and the throws are set up according to the manual.

❏

7. Make sure any servo wires do not interfere with other

systems (servo arms, pushrods, etc.).

❏

8. Balance your propeller (and spare propellers).

❏

9. Tighten the propeller nut and spinner.

❏

10. Place your name, address, AMA number and telephone

number on or inside your model.

❏

11. If you wish to photograph your model, do so before

your ﬁ rst ﬂ ight.

❏

12. Range check your radio when you get to the ﬂ ying ﬁ eld.