ADEMCO VISTA 5140XM Benutzerhandbuch - Seite 11
Blättern Sie online oder laden Sie pdf Benutzerhandbuch für Sicherheitssystem ADEMCO VISTA 5140XM herunter. ADEMCO VISTA 5140XM 15 Seiten. Commercial fire & burglary alarm system
Seite druckenFIRE & BURGLARY COMMON FEATURES
TROUBLE CONDITIONS
Your system monitors each of your fire and burglary protection zones and various system
conditions for problems such as zone wire breaks, loss of AC power, faulted telephone
lines, etc. which can compromise proper alarm signalling operation. When your system
detects a problem, it will provide an audible and visual "trouble" indication as described
below. When one of these indications appears, CALL YOUR INSTALLER FOR SERVICE
IMMEDIATELY. The audible indication can be silenced as described below.
1. The console sounder will produce a
rapid beeping. The external fire (and
burglary) sounders will not be on. The
console display window will display one
of the following messages:
•
"AC LOSS" when AC power has been
interrupted. The green console
POWER indicator will also be off.
•
"SYSTEM LO BAT" when your systems
back-up battery is low.
•
"COMM FAILURE" when attempts to
send a message to the central
monitoring station have failed.
•
"CHECK" accompanied by a protection
zone number (1-64) or a system zone
number (70-99) and an associated
alpha descriptor when there is a
protection or "system" zone problem.
See
the
section
"BYPASSING
SYSTEM ZONES AND OUTPUTS" for
a list of zone numbers reserved for
displaying system problems.
– 20 –
2. Press any key to silence the console
sounder.
3. To clear the console trouble display,
first, have your installer locate and
correct the cause of the problem. Then
enter any user code and press the OFF
[1] key.
NOTE: The display will not clear while the
trouble condition remains.
FIRE & BURGLARY COMMON FEATURES
BYPASSING SYSTEM ZONES AND SYSTEM OUTPUTS
NOTE: Ask your installer if your system was set up to allow system zones and
system outputs to be bypassed.
Your system may allow you to bypass certain "system zones" which monitor various
aspects of system status and certain system outputs which annunciate system status.
These zones and outputs are listed below. This feature is used to disable the monitoring of
one or more system zones or to disable the operation of one or more system outputs when,
for example, the system is to be serviced or tested. If enabled, this feature can only be
used by a master user.
•
zone
#70:
monitors
supervision status of the bell 1 output (if
enabled at installation time). Bypassing
this zone disables the operation and
supervision of the bell 1 output.
•
zone
#71:
monitors
supervision status of the bell 2 output (if
enabled at installation time). Bypassing
this zone disables the operation and
supervision of the bell 2 output.
•
zone #72: monitors the panel's
field wiring to determine if a short to earth
ground exists. Bypassing this zone
disables earth ground fault monitoring.
•
zone #73: monitors devices that
your installer has connected to input 1 on
the main PCB J2 connector (such as a
back-up ALARMNET radio transmitter).
Bypassing this zone causes the system
to ignore the status of devices connected
to input 1.
•
zone
#74:
monitors
supervision status of the main dialer
output (if enabled at installation time).
Bypassing this zone disables the
operation and supervision of the main
dialer output.
To Bypass a System Zone or System Output:
1. Enter the master code. Then press
BYPASS [6] and enter the number(s) of
zone to be bypassed.
2. All bypassed zones will be sequentially
displayed when you are finished
entering the number of zones to be
bypassed. The console will then
display a bypass message as a
reminder that one or more zones is
bypassed.
the
•
zone #75: monitors the
supervision status of the back-up dialer
output (if installed and enabled at
installation time). Bypassing this zone
disables the operation and supervision
of the back-up dialer output.
the
•
zone #76: this zone is
assigned to the auxiliary relay output.
Actually, this zone does not monitor
anything since the auxiliary relay output
is not supervised. However, bypassing
this zone allows the operation of the
auxiliary relay output to be disabled.
•
zone #77: this zone is
assigned to the ALARMNET radio
trigger outputs. Actually, this zone does
not
monitor
anything
ALARMNET triggers are not supervised.
However, bypassing this zone allows the
operation of the triggers to be disabled.
the
3. Zones which have been bypassed can
be displayed by entering any user code
and then pressing the BYPASS [6] key.
Bypassed zones will then be displayed
sequentially.
4. All system zone bypasses are removed
when an OFF sequence (code + OFF)
i s
p e r f o r m e d .
since
the
– 21 –