2gig Technologies 2GIG-FT1-345 Handbuch

Blättern Sie online oder laden Sie pdf Handbuch für Sicherheitssensoren 2gig Technologies 2GIG-FT1-345 herunter. 2gig Technologies 2GIG-FT1-345 2 Seiten. Flood and temperature detector
Auch für 2gig Technologies 2GIG-FT1-345: Einbauanleitung (2 seiten)

Seite drucken

2GIG-FT1-345

FLOOD AND TEMPERATURE DETECTOR

INSTALLATION INSTRUCTIONS

The 2GIG-FT1-345 is a fully supervised, tamper protected one-way 345 MHz

sensor. It will monitor the ambient temperature and/or will detect a wet/dry flood

condition. The sensor reports wet/dry conditions and temperature to the panel.

Flood Conditions

Once the sensor probe detects the presence of water for three (3) minutes, the

integral transmitter will send a wet alarm transmission to the panel. The probe will

also send a restore (dry) report when the presence of liquid is no longer detected

by the flood probe for three (3) minutes. For flood reporting the sensor requires

the installation of the supplied external flood probe. The sensor is capable of

detecting clean or dirty fresh water, salt water, or tap water.

Temperature Conditions

Heat:

1. If the temperature is more than 95° F (35°C) for five (5) minutes, the sensor

will send a loop 2 transmission.

2. If the temperature is less than 95°F (35°C) for five (5) minutes, the sensor will

send a loop 2 clear.

Cold:

1. If the temperature is less than 41°F (5°C) for five (5) minutes, the sensor will

send a loop 3 transmission.

2. In the temperature is more than 41°F (5°C) for five (5) minutes, the sensor

will send a loop 3 clear.

Contents

Verify that the package includes the following:

• 1—2GIG Flood/Temperature Sensor

• 1—Sensor Mounting Plate

• 1—3V Lithium Battery ( Panasonic CR15H270 uninstalled)

• 3—3/8" Phillips Screws

• 1—Double Stick Tape Strip

• 1—Probe Mounting Plate

Installation Tools Required

• Phillips Screwdriver

Figure 1.Temperature/Flood Sensor Contents

A Double Stick Tape Strip

B Sensor Mounting Plate

C Probe Mounting Plate

D 3V Lithium Battery

E Phillips Screws (3/8")

F Flood Probe Cord

G Flood Probe

H Transmitter with Integral Temperature Sensor

Installing and Replacing Battery

Open Sensor Case as show in Figures 2 and 3.

Install or replace battery.

Figure 2. Opening Sensor Case

Grip the base of the sensor case. Place thumb on tab and push down until sensor

case separates.

Figure 3. Separate Sensor Case

Figure 4. Installing New Battery

BATTERY

Installing a New Battery and System Programming

NOTE: Do not install battery until panel is in Sensor Programming Mode.

1. Place panel in Sensor Programming mode

2. Insert battery

3. Close sensor

Replacement Battery Installation:

NOTE: If battery has been previously installed

1. Remove battery and dispose of (meeting state regulations)

2. Wait two (2) seconds

3. Replace battery

4. Close sensor

Installing/Mounting Flood/Temperature Sensor

The 2GIG-FT1-345 Flood and Temperature Sensor includes two methods of

installation:

1. Double Stick Tape Installation (See Figure 5).

2. Screw/Mounting Plate Installation (See Figure 6).

It is strongly recommended that the Flood/Temperature Sensor be mounted using

screws (provided) and Mounting Plate (provided).

Figure 5. Double Stick Tape Mounting Sensor Mounting Plate

APPLY DOUBLE STICK

TAPE TO BACK OF

MOUNTING PLATE

FLOOD/

TEMPERATURE

SENSOR

MOUNTING

PLATE

1. PUSH DOWN ON

THUMB TAB.

2. PULL BACK PLATE

OFF OF COVER

REMOVE SENSOR

COVER FROM

SENSOR BASE

TEMPERATURE/

FLOOD SENSOR

BASE

BATTERY REMOVAL

AND/OR INSTALLATION

WALL

FIRST

PUSH

SENSOR

ONTO

MOUNTING

DOUBLE

PLATE

STICK

TABS

TAPE

THEN PUSH

STRIP