Emergi-Lite Lux-Ray LED Handbuch - Seite 2
Blättern Sie online oder laden Sie pdf Handbuch für Beleuchtungsanlagen Emergi-Lite Lux-Ray LED herunter. Emergi-Lite Lux-Ray LED 2 Seiten. Emergency lighting
Auch für Emergi-Lite Lux-Ray LED: Handbuch (2 seiten)
Seite druckenThread 1/2-14
Install ground
wire here
Back plate
Figure 2
6. Close the inside cover and tighten the screw.
7. Remove the unit housing from the package. Units with DC-remote
power: go to step 8 (see figure 3).
a. Units with battery back-up: plug the battery connector in the slot.
The connector is polarized, do not force-fit . Correct installation
has the positive red wire at the left (see figure 3).
b.
Units with dual AC circuit: connect the orange wire labeled
"VOLTAGE SELECTOR" to one of the two wires labeled AC
VOLTAGE (black: 120V; orange: 277V).
8. Hook the security wire to the backplate and tighten the screw (see
figure 3).
9. Align the unit housing over the back plate and press until it snaps in
place (see figure 4).
10. Energize the circuits. Units with battery back-up will have the test
button illuminated.
Backplate
Hook and tighten the security wire
Figure 3
Figure 4
Back plate
Emergi-Lite®
Tel: (888) 552-6467
®
Conduit (not supplied)
Liquidtight™ fitting
(not supplied)
Quick connect
Connect
battery
-
+
Housing
Housing
Testing the emergency lights
Allow the unit to charge for 24 hours before testing. Press the test but-
ton. The unit will light in emergency mode for one minute. To abandon
the test press the test button again.
Testing the normal lighting
Turn the AC power on: the unit will light.
Units equipped with photo-switch: mask the small circular window with
the finger: the unit will light. Uncover the window: when exposed to
ambient light the unit will turn off.
Maintenance
None required.
WARNING: Hold the housing in your hand and open the unit with a flat
head screwdriver. When replacing the housing assembly ALWAYS
hook and tighten the security wire.
Disconnect the battery if the emergency power supply is disabled for
two months or more.
Self-diagnostics / self-test (battery units)
1. Once supplied with power the unit will automatically initiate self-
diagnostic routines and a self-test calendar as follows:
a. Verifies battery connection, battery failure, charger board failure
and lamps failure.
b. Executes one-minute monthly self-test.
c. Executes a 30-minute self-test every 6th month.
d. Executes a 90-minute self-test every 12th month.
2. The LED pilot light is bi-color and indicates the following status:
a. Green color: AC-on / self-test
b. Red color: Service alert (see figure 5)
Battery
3. Transfer time delay (TD option)
This function acts when the AC power was restored: it keeps the emer-
gency lights "on" for a period of: 5, 10 or 15 minutes (factory-set). If the
battery depletes before the end of the time delay, the lamps turn off and
the unit goes in stand-by mode.
O
green
O
green
O
red
O
red
O O
red
O O O
red
Figure 5
Warranty: For the complete warranty information, please refer to the
landing page of our website (http://www.emergi-lite.com/usa/).
Fax: (800) 316-4515
www.emergi-lite.com
Lux-Ray LED - Emergency lighting
Steady
AC on
Blinking
Testing Mode
Steady on
Battery Disconnect
One Blink
Battery Failure
Two Blinks
Charger Failure
Three Blinks
Lamp Failure
02/18 750.1712 Rev. D
2/2