AirCycler SmartExhaust Handbuch - Seite 2
Blättern Sie online oder laden Sie pdf Handbuch für Controller AirCycler SmartExhaust herunter. AirCycler SmartExhaust 2 Seiten. Bath fan/ light switch /delay timer/ventilation controller
Seite drucken
SmartExhaust™ Instruction & Operation Manual
1) Do not connect this device to aluminum wire. Use with copper or copper clad wire only.
2) TURN POWER OFF at circuit breaker of fuse panel.
3) Remove cover plate and existing switch from wall box if there is one already installed.
4) Connect the wires in the wall box using the supplied wire nuts. Wires must have ¾ inch of bare copper ex-
posed. Twist wires together tightly with supplied wire nuts. Make sure no bare copper is exposed. Secure con-
nections with electrical tape. If a light is not connected, be sure to attach a wire nut to unused blue wire and
secure with electrical tape.
5) Mount SmartExhaust™ switch in to wall box with supplied mounting screws.
6) Set desired DELAY time by turning dial to desired minutes.
7) Set desired VENTILATION time by turning dial to desired minutes per hour.
8) Turn on power at circuit breaker or fuse box.
operating instructions:
• Move toggle switch up to turn on fan and light.
• Move toggle switch down to turn off light. Fan will run for set DELAY
time.
• To cancel DELAY time, move toggle up again for at least 1 second then
down again.
• Fan will shut off, cancling set delay time.
• DELAY will not activate if light/fan has not been on for at least 10
seconds.
• Fan will automatically come on once per hour for set VENTILATION
Any manual fan operation and DELAY operation will be subtracted from VENTILATION time
for that hour. If manual fan operation and DELAY operation exceed set VENTILATION time, the
excess time will be subtracted from the next hours VENTILATION time.
The SmartExhaust™ has a small microprocessor in it. The microprocessor reads the two settings dials.
If for example the VENTILATION dial is set to 20 minutes/hour, the microprocessor subtracts 20 min-
utes from 60 minutes and determines it needs to come on 40 minutes into the hour and run for the
remaining 20 minutes of that hour.
Now if the DELAY dial is set to 10 minutes and someone uses the bathroom for 4 minutes, the micro-
processor will keep track of the 4 minutes of use. Then when the person leaves after 4 minutes and
turns the light switch off, the micro will keep the fan on for 10 more minutes of the DELAY setting. This
will add up to 14 minutes of total fan run time for that hour. The micro will now subtract the 14 minutes
of manual and delay time from the required 20 minutes of VENTILATION time and come up with 6
minutes needed to run at the end of the hour. So 54 minutes into the hour the fan will come on and
run for 6 more minutes. Resulting in 20 minutes of total run time that hour.
what if manual and DElaY time exceeds VENTILATION time? The micro will calculate the excess
ventilation time and subtract it from the total VENTILATION time for the next hour.
what if you don't want the DElaY time to run after you use the bathroom? When the person leaves
the bathroom and shuts off the light, if they turn it back on with in 3 seconds and then back off with in
3 more seconds, the micro will kill the DELAY time for that use.
what if you're only in the bathroom for 5 seconds? You have to have the switch on for 10 full seconds
before the micro will start counting time and enable the DELAY function. If you turn the switch back
off with in 10 seconds, the fan shuts off and no time is counted.
For purchasing information, contact:
1)
Do not connect this device to aluminum wire. Use with copper or copper clad wire only.
2)
TURN POWER OFF at circuit breaker of fuse panel.
3)
Remove cover plate and existing switch from wall box if there is one already installed.
4)
Connect the wires in the wall box using the supplied wire nuts.
Wires must have ¾ inch of bare copper exposed. Twist wires together tightly
with supplied wire nuts. Make sure no bare copper is exposed.
Secure connections with electrical tape. If a light is not connected, be sure to
attach a wire nut to unused blue wire and secure with electrical tape.
5)
Mount SmartExhaust™ switch in to wall box with supplied mounting screws.
6)
Set desired DELAY time by turning dial to desired minutes.
7)
Set desired VENTILATION time by turning dial to desired minutes per hour.
8)
Turn on power at circuit breaker or fuse box.
Operating instructions:
Move toggle switch up to turn on fan and light.
Move toggle switch down to turn off light. Fan will run for set DELAY time.
To cancel DELAY time, move toggle up again for at least 1 second then down again.
Fan will shut off, cancling set delay time.
Delay will not activate if light/fan has not been on for at least 10 seconds.
Fan will automatically come on once per hour for set VENTILATION time.
Any manual fan operation and DELAY operation will be subtracted from VENTILATION time for that hour.
If manual fan operation and DELAY operation exceed set VENTILATION time, the excess time will be subtracted
from the next hours VENTILATION time.
Ventilation
Example: 10 minute delay,
20 minutes per hour ventilation
A Division of Lipidex Corporation
411 Plain Street
Marshfield, MA 02050
1)
Do not connect this device to aluminum wire. Use with copper or copper clad wire only.
2)
TURN POWER OFF at circuit breaker of fuse panel.
3)
Remove cover plate and existing switch from wall box if there is one already installed.
SmartExhaust™ Instruction Manual
4)
Connect the wires in the wall box using the supplied wire nuts.
Wires must have ¾ inch of bare copper exposed. Twist wires together tightly
with supplied wire nuts. Make sure no bare copper is exposed.
1)
Do not connect this device to aluminum wire. Use with copper or copper clad wire only.
Secure connections with electrical tape. If a light is not connected, be sure to
2)
TURN POWER OFF at circuit breaker of fuse panel.
attach a wire nut to unused blue wire and secure with electrical tape.
3)
Remove cover plate and existing switch from wall box if there is one already installed.
5)
Mount SmartExhaust™ switch in to wall box with supplied mounting screws.
4)
Connect the wires in the wall box using the supplied wire nuts.
Wires must have ¾ inch of bare copper exposed. Twist wires together tightly
6)
Set desired DELAY time by turning dial to desired minutes.
with supplied wire nuts. Make sure no bare copper is exposed.
Secure connections with electrical tape. If a light is not connected, be sure to
7)
Set desired VENTILATION time by turning dial to desired minutes per hour.
attach a wire nut to unused blue wire and secure with electrical tape.
5)
Mount SmartExhaust™ switch in to wall box with supplied mounting screws.
8)
Turn on power at circuit breaker or fuse box.
6)
Set desired DELAY time by turning dial to desired minutes.
Operating instructions:
7)
Set desired VENTILATION time by turning dial to desired minutes per hour.
Move toggle switch up to turn on fan and light.
8)
Turn on power at circuit breaker or fuse box.
Operating instructions:
Move toggle switch down to turn off light. Fan will run for set DELAY time.
To cancel DELAY time, move toggle up again for at least 1 second then down again.
Move toggle switch up to turn on fan and light.
Fan will shut off, cancling set delay time.
Move toggle switch down to turn off light. Fan will run for set DELAY time.
To cancel DELAY time, move toggle up again for at least 1 second then down again.
Delay will not activate if light/fan has not been on for at least 10 seconds.
Fan will shut off, cancling set delay time.
Fan will automatically come on once per hour for set VENTILATION time.
Delay will not activate if light/fan has not been on for at least 10 seconds.
www.aircycler.com
Fan will automatically come on once per hour for set VENTILATION time.
Any manual fan operation and DELAY operation will be subtracted from VENTILATION time for that hour.
If manual fan operation and DELAY operation exceed set VENTILATION time, the excess time will be subtracted
Any manual fan operation and DELAY operation will be subtracted from VENTILATION time for that hour.
from the next hours VENTILATION time.
If manual fan operation and DELAY operation exceed set VENTILATION time, the excess time will be subtracted
from the next hours VENTILATION time.
Ventilation
Ventilation
Example: 10 minute delay,
20 minutes per hour ventilation
Example: 10 minute delay,
20 minutes per hour ventilation
time.
SmartExhaust is a registered trademark of Lipidex corp.
A Division of Lipidex Corporation
Patents and Patents pending.
411 Plain Street
1-877-FAN-CONTrol (326-2668)
Marshfield, MA 02050
A Division of Lipidex Corporation
Black - Hot
411 Plain Street
Marshfield, MA 02050
Green - Ground
White - Neutral
FOR SUPPLY CONNECTIONS, USE 18 AWG OR LARGER
WIRES SUITABLE FOR AT LEAST 105 ˚C
SmartExhaust is a registered trademark of Lipidex corp.
Patents and Patents pending.
1-877-FAN-CONTrol (326-2668)
Lipidex Corporation
Ratings:
120VAC, 60 Hz, 5A
LISTED
Appliance Control
A Division of
A Division of
U.S. Patent
Lipidex Corporation
Lipidex Corporation
Pending
Ratings:
120VAC, 60 Hz, 5A
Ratings:
LISTED
120VAC, 60 Hz, 5A
Appliance Control
U.S. Patent
Pending
Ventilation
LISTED
Appliance Control
/Hour
U.S. Patent
Pending
Ventilation
Black - Hot
Black - Hot
Blue - Light hot
Green - Ground
Green - Ground
Red - Fan hot
White - Neutral
White - Neutral
FOR SUPPLY CONNECTIONS, USE 18 AWG OR LARGER
WIRES SUITABLE FOR AT LEAST 105 ˚C
FOR SUPPLY CONNECTIONS, USE 18 AWG OR LARGER
WIRES SUITABLE FOR AT LEAST 105 ˚C
SmartExhaust is a registered trademark of Lipidex corp.
Patents and Patents pending.
Blue - Light hot
1-877-FAN-CONTrol (326-2668)
Red - Fan hot
For more information call:
1-877-FAN-CONTROL
(1-877-326-2668)
www.aircycler.com
A Division of
Ventilation
/Hour
/Hour
Blue - Light hot
Red - Fan hot